Recommended Trailer Wiring Harness for 2020 Toyota RAV4

Question

Question:

Which trailer wiring harness would I need for a 2020 Toyota RAV4. I already have a hitch installed.

asked by: Robert

0

Expert Reply:

I'd recommend going with the Curt # C56434, which would install as shown in the video I've linked for you. The Curt harness is rated for more amperage than the Tekonsha model, which I why I recommend it.

expert reply by: Mike L

0

Answer 1

Extending the black power wire to the battery of the 2020 Toyota RAV4 from the Curt T-Connector part #C56434 can be done in a couple of ways. You can route the wire through the frame under the vehicle or route the wire through the vehicle itself. The…

view full answer...

Answer 2

If you check out the install picture I attached for the Curt hitch part #C13416 you can see that it hangs at the same height as the exhaust pipes and only sticks out a little bit past them so you'd have the same ground clearance you have now. Or…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

For your 2024 Toyota RAV4, the best trailer hitch receiver that will fit is the following: - etrailer Trailer Hitch Receiver #e23ZR The #e23ZR is the best because it has completely concealed crosstube so only the receiver is showing, allowing your…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Recommended Trailer Wiring Harness for 2020 Toyota RAV4

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching