What is the Center to Center Mounting Hole Measurement for Peterson Clearance Light LED 168A

Question

Question:

I need to know what the bolt center is on this light. I am looking to replace a bulb version of this light with the LED. The problem is my pace is limited on width. I have a max of 1 inch. the light I am replacing has bolt holes at 2 3/4 center to center. The technical data does not show what the bolt center to center is.

asked by: Tim H

0

Expert Reply:

There is a diagram on the page, below the bullet points for the Peterson light, # 168A, that shows the center to center hole measurement is 1-15/16 inches. I made a picture for you as well. You may also need a base, # B168-18 or # B168-10.

expert reply by: Michael H

0

click to enlarge

Answer 1

Ideally, you want the coupler sitting flat in direct contact with the top of the trailer tongue. If the gap between the bottom inside of the coupler and the trailer tongue is pretty minimal, say 1/16 of an inch or less, having it the way it is would…

view full answer...

Answer 2

The CE Smith Roller-Style Guide-Ons #CE27610 will fit your 2 x 2-inch trailer frame. The standard included brackets work with frame members up to 3-inches wide and 4-1/4-inches tall. It is a good idea to add another u-bolt to each guide-on in your…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 5

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

To replace your WFCO WF-8750P power center I recommend the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K. This 2-in-1 AC/DC distribution panel and converter charger keeps your power systems easily…

view full answer...

Answer 8

You'd need a new panel like the Progressive Dynamics Mighty Mini part #PD4045KA which is the most similar to your Parallax 7345 except is Lithium battery compatible. There isn't a center section replacement available for what you have that…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

Thanks for submitting the picture of the lights you are looking for. Based on that it looks like you are in need of a 194 bulb like the part #A194B.

view full answer...

What is the Center to Center Mounting Hole Measurement for Peterson Clearance Light LED 168A

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching