Trailer Hitch for 1995 Dodge B3500 RV

Question

Question:

i would like a hitch for my rv front Bumper for winch or pulling or cargo mat

asked by: Raymond A

0

Expert Reply:

There is a trailer hitch for your 1995 Dodge B3500 RV, but it is a rear-mounted hitch; there aren't any front-mounted hitches that fit this particular vehicle. I confirmed with the manufacturer that the Curt Trailer Hitch Receiver # C13041 is a fit for a '95 Dodge B3500 so long as it does not have a factory step bumper.

I have added a link to the instruction manual of the hitch for you to check out as well.

expert reply by: Kyle S

0

Answer 1

The Curt #13590 is confirmed to fit on the 1997 Dodge B3500 that has the factory step bumper. If your van doesn't have the step bumper, an option is the Curt #C13041. Both are designed for the Dodge Vans and are built to accomodate the…

view full answer...

Answer 2

Our Curt Trailer Hitch Receiver #C13041 and #13590 that are designed to fit your 1997 Dodge B3500 Van both have a width of 40" from the bolt hole center to bolt hole center. The Curt #C13041 is to be used with a standard bumper while the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Trailer Hitch for 1995 Dodge B3500 RV

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching