Can I Fit a Padlock On the Latch of the Pivot Lock Hitch Pin?

Question

Question:

Could I use a padlock to secure the pivoting lock pin, to make it more secure? I know there are locking hitch receivers but they all use keys and I want to use a combination lock.

asked by: Danny

0

Expert Reply:

You can use a combination padlock on the Pivot Lock Hitch Pin # 37201031, but you would need to find one with a shackle diameter of less than .25" to fit in the slot on the latch. The Master Lock Combination Padlock # ML4688D has a thin cable shackle with a .125" diameter and would be a good fit on this hitch pin.

expert reply by: Erik B

0

click to enlarge

Answer 1

A 5/8" diameter hitch pin is usually made of steel, though some have coatings applied to help resist corrosion. For example, the Master Lock Pivot Lock Hitch Pin for 2" Hitches #ML1465DAT is made of stainless steel, but there is also a…

view full answer...

Answer 2

7-Way trailer connectors have a male and a female side and the male installs on the trailer side and the female on the tow vehicle. That's why you are seeing them labelled differently. The part #54006-009 is a trailer side 7-way like it sounds…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...