Shipping Weight Of TorkLift GlowStep Stow N' Go Scissor Steps TLA7835

Question

Question:

What is the shipping weight of the 5 step torklift

asked by: Don

0

Expert Reply:

The shipping weight of the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 5 Steps - 325 lbs - Black Bracket part # TLA7835 is 40 lbs.

expert reply by: Heather A

0

Answer 1

A set of the TorkLift GlowStep Stow N' Go Scissor Steps #TLA7835 which uses the TorkLift GlowStep Stow N' Go Mounting Bracket #TLA7810 cannot be used as a step in the stowed position. You will therefor need to step over the steps to get in…

view full answer...

Answer 2

I went to the warehouse and took a measurement of the Brophy Camper Scissor Steps, part #AS05 for you. The distance form the top mounting bracket to the front of the lowest step is 39-1/4 inches. The distance form the frame below the lowest step is…

view full answer...

Answer 3

The 2-step #RHS2 is the only multi-step hitch mounted steps that I have seen. You might want to look at steps #TLA7806. You can attach these steps to the threshold and they will reach all the way to the ground when pulled out. They also feature…

view full answer...

Answer 4

In regards to the TorkLift GlowStep Stow N' Go Scissor Steps part #TLA7833, there is indeed a 6-1/2" gap between the first/last step and the mounting plate. This is needed in order for the steps to fully retract. It is not the intention of…

view full answer...

Answer 5

The Brophy Camper Scissor Steps for truck campers, #AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points…

view full answer...

Answer 6

Yes, anytime you use a hitch extender or reducer like #HR26 you will lose about 1/3 of your hitches overall capacity. However, since you'll be towing a trailer that weighs between 4,500 to 5,000 lbs, the Brophy Hitch Reducer #HR26 will still work…

view full answer...

Answer 7

We have one solution that will work well, but you'll need to have a 2-1/2 inch hitch installed on your tow vehicle. The Brophy hitch extender part #HR26 is a 7 inch extension with a capacity of 10,000 lbs so it would work well.

view full answer...

Answer 8

Yes, the Brophy Hitch Reducer and Extender #HR26 has more than enough depth from the face of the receiver to the pin hole for the 1-1/2 inch requirement of your Thule bike rack.

view full answer...

Answer 9

To verify if you will be able to use the Brophy Hitch Reducer and Extender #HR26 as both an adapter and a reducer you will need to measure your current receiver. The hitch pin center hole to the weld on the tube is 1-1/2" and 9-1/2" from…

view full answer...

Answer 10

I checked with TorkLift for you, and they do have a hitch that fits a 2022 Ram 4500 cab and chassis, with the correct fit being the following: - TorkLift SuperHitch Magnum Trailer Hitch Receiver #TL49YR Then, because of the overhang you mentioned,…

view full answer...

Answer 11

The mounting bracket height you see listed for the TorkLift GlowStep Stow N' Go Scissor Steps #TLA7836 is the ideal distance from where the bracket will mount below the door threshold to the ground. Based on the height clearance you mentioned…

view full answer...

Answer 12

The Replacement Jack for HappiJac Truck Camper Jack Systems #LC736515 is a replacement leg for the HappiJac Electric Truck Camper Jack System #LC736515-ELKIT that replaced the 4800 series jacks. These jacks lift 2" taller at 36-1/2" and are…

view full answer...

Shipping Weight Of TorkLift GlowStep Stow N' Go Scissor Steps TLA7835

Product Page this Question was Asked From

Continue Researching