Fitment of Brophy Camper Scissor Steps for Truck Campers

Question

Question:

Will it fit my rig? I have a 2009 Toyota Tundra with a 2001 north star TC-800, will the AS04 fit that combo?

asked by: Steve S

1

Helpful Expert Reply:

The Brophy Camper Scissor Steps for truck campers, # AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points and chart.

expert reply by: Michael R

1

AS04_001
(click to enlarge)

Chart_
(click to enlarge)

Answer 1

When folded up into the stored position the TorkLift GlowStep Camper Scissor Steps #TLA7802 are approximately 9-1/2" deep. I confirmed with TorkLift that this specific model is designed to just fold up, lock in place and be ready to travel.

view full answer...

Answer 2

The Brophy Clamp On Camper Tie-Downs #HSSF will have a very slight amount of play since there is a compressible pad to prevent scratches on the bedrails, but it sounds like you're having much more significant play. I've attached a picture…

view full answer...

Answer 3

That is correct, you can tap into the plug and it will provide a charge but keep in mind that this is not the most efficient way for charging a battery. This method does not provide any charge balancing or battery charge management and on newer…

view full answer...

Answer 4

The Aluminum Scissor Steps #AS03 that you referenced weigh 15 lbs and the Scissor Steps #SS03 weigh 29 lbs. As you can see, aluminum is much lighter.

view full answer...

Answer 5

The Brophy Camper Scissor Steps part #SS03 weigh 27 lbs total.

view full answer...

Answer 6

If you check out the install picture I attached for the #AS23 you can see where it normally installs at the rear of a camper that is installed on a truck. Without seeing your setup it's hard to be more specific but there should be a spot on the…

view full answer...

Answer 7

The HSSF hold down brackets would use the Tie Down Hardware Package, part #TDHP, which includes hooks, chain and turnbuckles. The tie down hardware would typically attach to existing eye bolts built into the underside of camper. If your camper does…

view full answer...

Answer 8

The bracket of the Aluminum Scissor Steps #AS04 that you referenced stays attached to the camper, but the steps themselves get removed while traveling. Check out the review video I attached for these steps as well.

view full answer...

Answer 9

It is too small of a space to fit the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375lbs - Black Bracket Item #TLA7834 but you can instead mount it to the bumper of your camper like in the attached picture.

view full answer...

Answer 10

For your 2005 Dodge Ram 1500 and the Brophy camper tie downs #TDSF you will need hardware that is the right grade and for the right material (in this case steel) just longer than the included hardware. I recommend using grade 8 hardware. A hardware…

view full answer...

Answer 11

The TorkLift GlowStep Stow N' Go #TLA7844 weighs just over 30 (about 32) lbs by itself. The TorkLift GlowStep part #TLA7804 and part #TLA7504 both weigh a little over 20 (about 22) lbs each.

view full answer...

Answer 12

We do not have a 20" wide quick attach model of step similar to the TorkLift GlowStep Camper Scissor Steps #TLA7802. The closest we have to 20" wide that are detachable are the Brophy Camper Scissor Steps #SS02 which are 17" wide.

view full answer...

Fitment of Brophy Camper Scissor Steps for Truck Campers

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching