Baby Moon Hub Caps for 1958 Chevy Apache Pickup with 17.5" Wheels

Question

Question:

I have a 1958 Chevy Apache 3/4 ton pickup with 17.5inch wheels. i am missing one babymoon hubcap. the wheels have tabs on them to hold the cap on. do you have a replacement cap?

asked by: Bill P

0

Expert Reply:

I did some looking around and it looks like we only have baby moon hubcaps that would work on as large as 16" diameter wheels, like the Phoenix USA Baby Moon Hub Cover 12" Diameter # PX1309SS. I've linked our entire selection of baby moon style hub caps for you to look at and see if there are any that you might be able to make work on your 1958 Chevy Apache in the event that you need smaller than 12" diameter baby moons.

expert reply by: Erik B

0

Answer 1

We do have exactly what you are looking for, hubcaps that fit 16 inch trailer wheels that have 8 lugs; what you need is the following: - Phoenix USA Baby Moon Hubcap #PX1309SS These fit 16" conventional wheels that have a 6 on 5-1/2" or 8…

view full answer...

Answer 2

The Phoenix USA #PX1307SS baby moon hub caps will only fit a conventional steel wheel like part #AM20514 with a 6 on 5-1/2 inch bolt pattern, because the raised lip around the lug holes is compatible with the inside dimension of the hubcap. Assuming…

view full answer...

Answer 3

Thank you very much for your follow up question. The Bearing Buddy Bearing Protectors #BB2717 are designed to work with outer bearing model 14125A and outer bearing cup (race) model 14276, which are commonly found on 7,000-lb Dexter axles. Most…

view full answer...

Answer 4

Yes. The Phoenix USA Baby Moon Hub Cover - 12" Diameter - Stainless Steel #PX1309SS is designed to work on 16" conventional wheels, so these will be a fit for your 1968 C20 with 16" wheels.

view full answer...

Answer 5

Yes. The nubs on the wheel are simply to hold the Phoenix USA Baby Moon Hubcaps #PX1309SS into place, so the 4th nub will just give you one more spot where they're holding these into place. For this reason they'll work just fine on your…

view full answer...

Answer 6

The Dexstar Conventional Steel Wheel 16" 8 Lug part #AM20766 is only offered with an offset, +.5" to be exact. The majority of the conventional style that accept the baby moon hubcaps part #PX1309SS have an offset. That said, if you're…

view full answer...

Answer 7

The overall diameter of the baby moon cover part #PX1309SS is 12 inches and the inner diameter is 11-15/16 inch.

view full answer...

Answer 8

Do you see the three raised bumps on the center circle section of your wheel? That's where a baby moon like the part #AM90086 fits over. You need to measure that diameter. If it's right at 9-1/4 inch this cover is what you'd need.

view full answer...

Answer 9

Selecting the correct Bearing Buddy bearing protector for your 8-lug hubs requires that you know the hub's bore where the grease cap (or Bearing Buddy) fits. This requires using a precision digital or dial caliper and measurement to the nearest…

view full answer...

Answer 10

The Break-Away Kit and Battery, part #HBA-EBA, for the Hydrastar Electric-Hydraulic Actuator, part #HBA-10, is the correct unit to provide power to the hydraulic pump for the specified amount of time to meet DOT regulations. The battery in this…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Baby Moon Hub Caps for 1958 Chevy Apache Pickup with 17.5" Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching