Mounting Dimensions Of The Bargman 7-Way Super Sealed Connector 50-87-004
Question:
I am wondering about the dimensions of this vehicle end 7 blade connector. How much width and height flat space do I need for bumper mounting and how far does the rigid end stick out on the other side of the bumper the part that tapers down to the wiring cord. So...I am looking for something like 3 inches wide by 2.75 inches high flat space on the outside of the bumper and that it for example sticks out behind the bumper 5 inches before the cord can flex a different direction. I am just making these numbers up and am hoping you can give me the exact measurements. And do you ship to Canada? Thanks,
asked by: Paul C
Helpful Expert Reply:
I went to the warehouse and pulled a 7-Way Super Sealed Connector # 50-87-004 to measure. This connector provides 4 feet of cable, is 6" from the front edge of the trap door/cap back to where the cable flare ends. The mounting plate measures 3" x 3" on the outer edges.
You will need a 2 inch hole in order to mount the Bargmann 7-Way Super Sealed Connector, # 50-87-004. I have attached a diagram which illustrates the exact measurements of the connector as well. We do ship to Canada and I hope this helps get you started.
Product Page this Question was Asked From
7-Way Super Sealed Connector w/4' Cable - Car End
- Trailer Wiring
- Trailer Connectors
- Vehicle End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 7 Round - Blade
- Bargman
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Reese Safety Chain Kit with Clevis Hooks - 44" Long - 20,000 lbs - Qty 2
- Search Results: reciever tube
- Shop: Combo Bar 12" with 2" Trailer Hitch Receiver - Unpainted
- Shop: Buyers Products Weld-On Receiver Tube with 2-1/2" Hitch Receiver - 12" Long - 20K
- Shop: 2-5/16" Hitch Ball - 2" Diameter x 3-1/2" Long Shank - Raw - 30,000 lbs
- Shop: 2-5/16" Hitch Ball w/ 1" Rise - 1-1/2" Diameter x 2-3/4" Long Shank - Raw - 30K
- Search Results: 7~ and 4~pole trailer connector socket
- Search Results: pintle hook
- Search Results: curt plug
- Search Results: 7 pin plug
- Search Results: curt 7 pin
- Search Results: trailer plug
- Shop: Trailer Wiring
- Q&A: Hole Size Needed for Mounting Hopkins Multi-Tow 7-Way Blade and 4-Way Flat Trailer Connector
- Q&A: Recommended 7-Way To Hopkins Molded Trailer Wire with Different Colors
- Q&A: Dimensions of Hopkins Multi-Tow 7-Way and 4-Flat Connector
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Shop: Curt 7-Way RV-Style Trailer Connector - Vehicle End
- Q&A: Dimensions of B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1500
- Q&A: Can the Curt 7-Way Extension be Used with a PowerMax Converter to Power Trailer
- Q&A: What is the Difference Between the Draw-Tite and Reese Versions of Dual Cam Sway Control
- Q&A: Curt vs. Draw-Tite Trailer Hitch Comparison for a 2016 Subaru Outback Wagon
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Video: B and W Ball and Safety Chain Kit Underbed Gooseneck Trailer Hitch Review
- Shop: Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Video: B and W Underbed Gooseneck Trailer Hitch Ball and Safety Chain Kit Install - 2021 Ram 3500
on Trailer Wiring
James G.
6/22/2020
Would you have a mounting pattern with hole size? We are looking to install these on our rear hitch plates that are 1" thick the pattern would be helpful to have it laser cut before hand.