Fulton Trailer Jack that Pivots for Boat Trailer Tongue

Question

Question:

I am looking for fulton brand clamp-on swing away, extended length boat jack. The jack I have isnt long enough to lift the hitch, high enough without putting a wood block under it. Can you help

asked by: Bill

0

Expert Reply:

We have the Fulton F2 Swing Up Jack part # F1413040134 which covers everything you said you are looking for. It's a bolt on style of jack that will fit the side of your boat frame well, it can pivot up and out of the way, has a 1,600 lb capacity, and provides up to 22 inches from where it attaches when fully extended.

expert reply by: Jameson C

0

Answer 1

If the swivel jack you have is a Fulton the sleeve washer that comes with the part #F0933325S00 that you referenced would replace what you have and would prevent your jack from leaning like you mentioned.

view full answer...

Answer 2

The Fulton Bolt-Thru Swivel Marine Jack part #FXP10W0301 is held on to the trailer with a center bolt. It is also the pivot bolt. Use a box end wrench or a short wall socket to remove the existing bolt. It has pretty coarse threads and generally…

view full answer...

Answer 3

If you want to avoid the hassle of trying to match up a new jack to the old mount on your trailer you can simply bolt on a new side-mount swivel jack like the Fulton F2 #F1413040134. The swiveling F2 fits 3 x 3 and 3 x 4 trailer tongues, features…

view full answer...

Answer 4

Based on the pictures you provided it looks like the mount on your 1999R71 Range trailer uses a jack very similar to the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301. You will need to confirm that this jack will be compatible by measuring the…

view full answer...

Answer 5

Thank you for the photo it was helpful in determining what you need. The replacement would be the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which has a bolt-through mount, 1,200 lb lift capacity and has bracket heights of 12-3/4" retracted…

view full answer...

Answer 6

In regards to mounting the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301 you'll need a mounting kit like the Bolt-On Mounting Kit for Fulton part #F500349 which contains the mount and the center bolt, nut, and tapered spacer. The only…

view full answer...

Answer 7

It looks like you have a Bolt-Thru style Fulton Swivel Marine Jack therefore the correct replacement for you would be part #FXP10 which has a 1,200 lb weight capacity. This jack would then use the same mounting bracket you have now but it does come…

view full answer...

Answer 8

You will be able to use the Bolt-On Mounting Kit #F500349 with the Mounting Hardware #F500286 to bolt on the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301.

view full answer...

Answer 9

I went out to our warehouse and measured the 4 holes in the center of the Replacement Bolt-On Mounting Bracket for Fulton XP Series Jacks #F500349, and they measure 3" on center left and right, and 3" on center up and down. The remainder of…

view full answer...

Answer 10

It sounds like you are actually needing the Replacement Hardware Kit for Fulton Swivel Jacks #F0933325S00.This fits a mounting plate like the #P9012-00 that it sounds like you have welded to your trailer. It includes the metal bushing/washer that you…

view full answer...

Answer 11

The 60/40 axle placement formula is a great starting point and does take into account the tongue of the trailer from where the trailer sits on the hitch ball. Please keep in mind that this is a very basic formula or estimate for axle placement. For a…

view full answer...

Answer 12

The shackle straps need to be placed on the outside of the rear leaf spring hangers which you can see in the attached photo. Furthermore, the distance between the two mounting plates (inside to inside) on your leaf spring hangers should be…

view full answer...