Similar Version of etrailer Side Mount Jack with at Swivel and Wheel Caster

Question

Question:

I ordered MJSQ-2500B yesterday, to replace my Ram rusted out jack on my boat trailer. wanted to know who is the manufacture? is there a Swivel Jack model that is similar? and is there a wheel that fits this model? Thanks

asked by: Sam

0

Expert Reply:

The etrailer.com jack part # MJSQ-2500B is made by RAM jacks like the jack you have now. The most similar swivel jack with a wheel caster would be the etrailer.com part # MJ-1200B which has a 1,200 lb capacity, a wheel like you want, and swivels like you want it to as well.

expert reply by: Jameson C

0

Answer 1

A solid replacement jack that I recommend is the Square Jack w/Footplate-Bolt On, Item #MJSQ-2500B. This item is a great marine jack that has a rust-resistant zinc finish and that is built to be flexible and durable. It has a lift capacity of…

view full answer...

Answer 2

The Fulton T1401 model has been discontinued. As a replacement I recommend the Fulton Single Speed Trailer Winch - 8" Long Handle - 1,500 lbs #F142201. The slightly smaller option is the Fulton Single Speed Winch - 8" Long Handle - 1,300…

view full answer...

Answer 3

The mounting holes on Square Jack w/ Footplate - Drop Leg - Bolt On - Zinc - Sidewind - 15-3/8" Travel - 2.5K Item #MJSQ-2500B are spaced 1" apart on center for the top 3 holes and bottom 3 holes. The 2 inner-most holes are spaced…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 12

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...