Correct Replacement for Lippert Power Gear Jack 181794

Question

Question:

Power gear Power Jack 181794

asked by: John

0

Expert Reply:

I am not sure what your exact question is but the Lippert Power Gear Jack 181794 has been discontinued and there are no replacement parts available for this. Therefore, if you have an issue with yours then you will need to replace the entire jack and the correct one for this is the Lippert Electric Trailer Jack with Footplate part # LC285318. There is also a more cost effective replacement as well, the Electric Jack w/ Footplate part # EJ-3520-BBX or part # EJ-3520-WBX. These three options will all be a direct bolt on replacement for your old Lippert Power Gear Jack 181794.

expert reply by: Conner L

0

Answer 1

For a Lippert jack model 181794 a replacement manual crank nut is not available. I checked with my contact at Lippert to confirm. You will need to replace your jack with a complete new one, I am sorry to say. To help you select a new one I have…

view full answer...

Answer 2

For the replacement top cover for your Lippert Electric Trailer Jack #LC285318 you will use the part #LC285160. This is the top plastic black cover that comes down over the switches. The protective lens for this jack is no longer available as a…

view full answer...

Answer 3

Lippert does not offer a replacement inner jack tube for their jack 1817941. When a jack is damaged in this way (which is more common than you want to know) it really is best to replace the entire jack for safety reasons. The outer tube on your…

view full answer...

Answer 4

I have a solution for you but they do not offer just the lens for individual sale. You will need to use the Replacement Bottom Jack Cover with Light Lens for Lippert Electric A-Frame Trailer Jacks item #LC23UD. This will replace the lens and the…

view full answer...

Answer 5

For your Lippert Electric Trailer Jack 1817941, the correct bottom jack cover is the Replacement Bottom Jack Cover with Light Lens for Lippert Electric A-Frame Trailer Jacks #LC23UD. If you ever should need the top cover as well, you can use the…

view full answer...

Answer 6

I have included the video and a link to the original answer page that also has the video you are looking for. There are 4 screws on the bottom of the bottom cover holding it to the top. And if you remove the cap on the very top of jack #LC285318…

view full answer...

Answer 7

Yes, I confirmed with Lippert that the Replacement Top Cover for Lippert Components Electric Trailer Jack part #LC285160 will fit your Lippert 3,500 Lb Electric tongue Jack 1817941.

view full answer...

Answer 8

To replace the extend/retract switch on your Lippert 181794 Electric Trailer Jack you'll simply need the Replacement Extend/Retract Switch for Lippert Electric Trailer Jack #LC49MD. If you're needing to replace the on/off or just…

view full answer...

Answer 9

Normally an intermittent working motorized jack like the Lippert Components Powered Tongue Jack #LC285318 is due to a faulty ground or a short circuit in the power wire. I recommend checking your ground connections, normally in the mount of the jack…

view full answer...

Answer 10

The problem you are describing on your Lippert Electric Trailer Jack part #LC285318 could be caused by a few different things. The most common problem we see that allows the light to work but not the leg is a bad ground. This could very well still…

view full answer...

Answer 11

For replacement Dexter manual adjust brake assemblies to replace your 36-19 you would want the part #23-27 for the right hand side and part #23-26 for the left hand side. These are manual adjust 10 by 2-1/4 inch Dexter brake assemblies that would…

view full answer...

Answer 12

The only tank equipped RV water heat option we currently offer is the Dometic RV Water Heater part #DMC74FR which is a 120 volt unit with 6 gallon tank and gas/electric operation. In regards to installation, this must be performed by a qualified…

view full answer...