Light on the Lippert Electric Trailer Jack Works but No Power to Leg

Question

Question:

I have a lippert power jack, looks like the Item # LC285318. it has just stopped working, the LEDs work but the jack doesnt work. I did have a problem blowing the 30 amp fuses last season but that isnt the problem this time. By batteries are fully charged and we are plugged into 110. This is the first time testing this season as well. Any ideas?

asked by: Dan

0

Expert Reply:

The problem you are describing on your Lippert Electric Trailer Jack part # LC285318 could be caused by a few different things. The most common problem we see that allows the light to work but not the leg is a bad ground. This could very well still allow for the light to function but not allow for enough power to operate the leg. I recommend checking the mounting surface that the jack is attached to since this is how it grounds. I would then remove the jack, sand down the surface with some sandpaper, and clean off the hardware with some parts cleaner.

If the newly finished ground does not fix the problem then you will want to take the top cap off of the jack and have a look inside while the power is supplied. If you hear any noise then it is likely that something has become loose or broken. If the jack was ever overextended then this could very well cause the problem you are having. If you do not hear any noise then chances are the motor is bad.

If the motor is bad and or some of the internal components have become damaged then the only option you have would be to replace it as we do not have any replacement parts for this jack. For a replacement, I recommend the Stromberg Carlson # SC63VR tongue jack. This jack has a 4,500 lb capacity which means that it will not have to work as hard which in turn extends its life. It also has an integrated stop that will not allow you to overextend the jack which could then cause damage.

I have attached a review video for you as well.

expert reply by: Conner L

0

click to enlarge

Answer 1

Normally an intermittent working motorized jack like the Lippert Components Powered Tongue Jack #LC285318 is due to a faulty ground or a short circuit in the power wire. I recommend checking your ground connections, normally in the mount of the…

view full answer...

Answer 2

I am not sure what your exact question is but the Lippert Power Gear Jack 181794 has been discontinued and there are no replacement parts available for this. Therefore, if you have an issue with yours then you will need to replace the entire jack…

view full answer...

Answer 3

For a Lippert jack model 181794 a replacement manual crank nut is not available. I checked with my contact at Lippert to confirm. You will need to replace your jack with a complete new one, I am sorry to say. To help you select a new one I have…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lippert does not offer a replacement inner jack tube for their jack 1817941. When a jack is damaged in this way (which is more common than you want to know) it really is best to replace the entire jack for safety reasons. The outer tube on your jack…

view full answer...

Answer 7

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 8

Hi Robert, So there isn't one that can be used with a cordless drill (which would be an electric jack only) as all the electric A-frame jacks are all higher than the 12" to 14" you want. There is a manual crank jack you can use which I…

view full answer...

Answer 9

Hi Robert, So I know you don't want to, but the only option for a hitch extension for your 2-1/2 inch hitch does reduce the receiver to 2 inches. I hope you're not mad at me, but there unfortunately is no 2-1/2 inch hitch extender that also…

view full answer...

Answer 10

Because of its functionality with the Electric Ground Control TT Automatic 5-Point Travel Trailer Leveling System #LC672136 you do need to replace the 421366 tongue jack with another one. The correct part is the following: - Replacement Tongue Jack…

view full answer...

Answer 11

It will indeed work; I just checked with Lippert for you and was able to verify the correct toggle switch for your Lippert Power Stance Electric Trailer Jack #LC69VR (which is the 813748), is the following: - Replacement Extend/Retract Switch for…

view full answer...

Answer 12

The inner lip of the Snap Pad Jack Pad for Camper Jacks w/ 5-1/2" Round Feet #SN97FR that grips onto the jack foot has a 5-1/8" measurement from one edge to the other so you'd have a bit more than 1/8" of the lip covering the jack…

view full answer...