Diameter Of Tube Accepted In Replacement Tripod Base For Brophy Cable Camper Jack

Question

Question:

Tripod base, code: 1003, Will this base work as a replacement for the Reico camper jack tripod base? What is the internal diameter of the Tripod cup? My Reico down tubes have an OD of 1.5

asked by: John D

1

Helpful Expert Reply:

The diameter of the pole that will fit into the Replacement Tripod Base for Brophy Cable Camper Jack - Qty 1 # 1003, is 1-1/2 inches. So, it appears this will work for your application.

expert reply by: Jason S

1

Answer 1

I spoke to my contact at Brophy and he informed me that the diameter of the pole that would fit the Replacement Tripod part #1003 that you referenced will be 1-1/2 inches.

view full answer...

Answer 2

I measured the inside diameter of the Replacement Tripod Base for Brophy Cable Camper Jacks #1106 and found it was 2 inches. This base is a replacement for the Brophy Cable Camper Jacks - 57" Max Lift Height #CJ41 and 67" Max Lift…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Hi Sean, We do offer the Ground Control 3.0 for prepped trailers part number 2021106810 as part #LC52ED. This is going to include the rest of the components needed to complete the system. Since we don't have a video of this kit yet I've…

view full answer...

Answer 7

We have excellent options for replacing your truck bed camper jacks but we do not have a way to get the gears you'd need for the jacks that you currently have. Based on that you'd want the Brophy Cable Camper Jacks #CJ31 which has a 1,000 lb…

view full answer...

Answer 8

The HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 have a minimum reach of 16-1/2". This means your tie-downs need to be at least 16-1/2" away from the attachment points on your camper. The best way to determine fitment would…

view full answer...

Answer 9

The handle on Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 5,000 lbs Item #TJDA-5000S is held to a gear with a roll pin and into the jack with e-clips. It would require modification and fabrication to link two of…

view full answer...

Answer 10

The Brophy Cable Camper Jacks #CJ31 has tripod feet with the longer two legs sitting at almost a 90 degree angle in proportion to the smaller leg. Since they don't sit at a perfect 90 degree angle they will be slightly under the L-brackets that…

view full answer...

Answer 11

The combined weight capacity of the Brophy Cable Camper Jacks #CJ31 is 1,000 lbs. I have linked the above mentioned product to this page for your purchasing convenience.

view full answer...

Diameter Of Tube Accepted In Replacement Tripod Base For Brophy Cable Camper Jack

Product Page this Question was Asked From

Continue Researching