Replacement for Dual Cam Swan Control 26001

Question

Question:

Model 26001 dual cam sway control. Need to replace cam arm. Cost for part?

asked by: Kevin K

0

Expert Reply:

The 26001 arms are no longer available and have been replaced by the Reese Dual Cam High-Performance Sway Control # RP26002. These are sold as a pair and not individually, so you would need to get both, and since you don't want to mix old parts and new, it is a good idea to replace both of your arms. You can find the price for these arms directly on the linked product page.

I have also added a link to a video review for you to take a look at.

expert reply by: Kyle S

0

Answer 1

Hi Joe, The Blue Ox Base Plate Kit #BX1139 is a confirmed fit for your 2024 Jeep Wrangler Rubicon X per Blue Ox. I don't currently have an installation video on a model with a steel bumper but I did measure from the mounting holes down to the…

view full answer...

Answer 2

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 3

Brien, it sounds like you did your research so kudos to you, but the awning you're looking at is not going to work with the wind sensor. You'd need to use the Solera Smart Arm 12V Power RV Awning #LC517517 instead. You're also going to…

view full answer...

Answer 4

Those are good questions. We would first want to confirm the specific model of Ram truck you have. The towing/pin weight capacities can vary between different model. Your owners manual should also specify the towing capacity and pin weight capacity.…

view full answer...

Answer 5

It's not uncommon to have a slide topper installed below the awning of the RV if the awning happens to be over the slide out. As long as you have room for a rail to fit under the main awning rail this would be totally fine. To pick out the…

view full answer...

Answer 6

Yes, you can remove the Shark Fin Camera Mounting Bracket #FRCBRKT-BL which includes the wiring from your 2024 Forest River Flagstaff Super Lite 26FKBS for a Voyager system. The Kit #ASA24YR you found is specifically designed for trailers pre-wired…

view full answer...

Answer 7

Sway controls are designed to be used in situations where sway is a direct result of some type of road condition, like high winds or large vehicles passing. If you have sway with a trailer under normal towing conditions, sway control will most likely…

view full answer...

Answer 8

It looks like your 2019 Lance 2465 travel trailer tops out at 6,830 lbs. The Strait-Line Weight Distribution w/ Sway Control item #RP66074 will work for you trailer. It has a tongue weight range of 600 lbs - 1,200 lbs which is perfect for your Lance…

view full answer...

Answer 9

The dual cam setups are still the best sway control around as they do the best at preventing sway before it starts due to the way they want to force the trailer to stay straight behind you. So the Strait Line part #RP66084 that you referenced would…

view full answer...

Answer 10

Based on your photo, it appears you have the dual cam system of the Reese Strait-Line. I researched your trailer to find a GVWR of 5895. Based on this, we can make some calculated assumptions on the tongue weight. The tongue weight of a trailer is…

view full answer...

Answer 11

The Reese and Draw-Tite products are manufactured by the same parent company, this means that the #26102 and #26002, Dual Cam Sway Control systems are the same, but there is a difference in the generations of the systems. The older systems had Hanger…

view full answer...

Answer 12

The individual links on a weight distribution system like the #RP66541 do not represent different tongue weight values. It really just comes down to following the setup procedure that is outlined in the install instructions which are attached which…

view full answer...