Weight of EcoHitch Stealth Trailer Hitch Receiver # 306-X7293

Question

Question:

Dear Sirs: Could you please advise the weight of the unit itself? Regards,

asked by: Charles T

0

Expert Reply:

The EcoHitch Stealth Trailer Hitch Receiver # 306-X7293 that you referenced weighs exactly 24.5 pounds.

The custom hitch features a towing capacity of 1,000 pounds and a tongue weight limit of 200 pounds.

expert reply by: Chris R

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Yes, when installing the EcoHitch Stealth Trailer Hitch Receiver part #306-X7293 on the 2019 Subaru BRZ the bumper panel needs to be removed with a flat head tool like a screw driver or part #ALL648544. The EcoHitch will be attached to the impact bar…

view full answer...

Answer 3

The EcoHitch Stealth Trailer Hitch Receiver #306-X7293 is a fit for your 2019 Subaru BRZ. The hitch is a hidden design to allow you a very clean look. The hitch cross tube is concealed behind the rear bumper and the receiver is removable when not in…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 10

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Weight of EcoHitch Stealth Trailer Hitch Receiver # 306-X7293

Product Page this Question was Asked From

Continue Researching