Does The Rear Bumper Panel Of 2019 Subaru BRZ Come Off To Install EcoHitch 306-X7293

Question

Question:

Does the rear panel of the 2019 Subaru BRZ come off to install the EcoHitch hitch 306-X7293

asked by: Pete

0

Expert Reply:

Yes, when installing the EcoHitch Stealth Trailer Hitch Receiver part # 306-X7293 on the 2019 Subaru BRZ the bumper panel needs to be removed with a flat head tool like a screw driver or part # ALL648544. The EcoHitch will be attached to the impact bar under the bumper fascia. I have attached a photo for your reference.

expert reply by: Heather A

0

Answer 1

The EcoHitch Stealth Trailer Hitch Receiver #306-X7293 is a fit for your 2019 Subaru BRZ. The hitch is a hidden design to allow you a very clean look. The hitch cross tube is concealed behind the rear bumper and the receiver is removable when not in…

view full answer...

Answer 2

The EcoHitch Stealth Trailer Hitch Receiver #306-X7293 that you referenced weighs exactly 24.5 pounds. The custom hitch features a towing capacity of 1,000 pounds and a tongue weight limit of 200 pounds.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Curt trailer hitch #C11379 has a shipping weight of 33 pounds, the heaviest of the hitches for your 2014 Scion FR-S. The hitches are designed to fit models that have the stock exhaust. They have not been tested on alternate exhaust systems. It is…

view full answer...

Answer 5

Yes, to install the Draw Tite hitch part #24935 that you referenced the rear panel does have to come off. In the instructions link that I attached this entire process is covered. For trailer wiring you then would want the part #118629 which is a…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Does The Rear Bumper Panel Of 2019 Subaru BRZ Come Off To Install EcoHitch 306-X7293

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching