Torklift Frame-Mount Camper Tiedowns for 2006 Chevy Silverado 2500HD 8 Foot Bed

Question

Question:

Re: Torklift, Chassis mounted front and rear Camper Tiedowns for Chev Silverado 2500 2006 HD, The Foot step rail stops at end of cab just before the 8 foot tray/bed. Please provide the correct Torklift model part numbers required to best fit this Chev Silverado HD 2500 year 2006 model which has a double cab. We have bought an over-cab camper to fit this 8 foot bed truck and Im recommended Torkliftfoot as opposed to Happy Jack. Required is the removable extension for both front and rear stanchions when the camper is not on board. Thank you

asked by: Robert C

0

Expert Reply:

The correct TorkLift camper tie downs for your 2006 Silverado 2500HD 8-foot bed with factory hitch, double/extended cab and steps that end at the cab are part # TLC2204 for the front set and # TLC3206 for the rear. Both have the removable arms you're looking for. For matching FastGun turnbuckles that lock use kit # TLS9529-2-LK.

expert reply by: Adam R

0

click to enlarge

Answer 1

The only 4-step aluminum steps we carry are scissor steps such as #AS24 but they are not designed for permanent installation on a 5th wheel trailer. For steps that are designed for permanent installation on a 5th wheel trailer you can use…

view full answer...

Answer 2

We have a couple of 4-step scissor stairs you could use. We have a steel model, #SS04, and an aluminum model, #AS04, and both are 18 inches wide. These stairs mount using an included bracket that looks like #AS2002. So they do not pin into place.…

view full answer...

Answer 3

It's possible you could take it to get repaired but it may be cheaper to upgrade your unit. The Jensen RV Stereo #JWM60A is identical to your Jensen AWM968L, and has the same cutout dimensions as your current unit, making this a direct…

view full answer...

Answer 4

For your 2000 Chevrolet Silverado 2500, with 8' bed, factory hitch, and no running board under the bed, you should use the TorkLift #TLC2202 (front) and #TLC3204 (rear) frame mounted camper tie-downs. The powder coated finish will look great…

view full answer...

Answer 5

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 6

Turnbuckles like theHappiJac Original #LC182898 are more or less universal so you'll be able to use them with the TorkLift Custom Frame-Mounted Camper Tie-Downs #TLT2303.

view full answer...

Answer 7

I spoke with HappiJac about the HappiJac Original Turnbuckles for Camper Tie-Downs part #LC182898 and they informed me that the max reach is 22" for the front and 33-1/2" for the rear. Please note, the turnbuckles are adjustable so you can…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...