Trailer Wheel Hub to Match 2,200 Pound Lippert Spindle

Question

Question:

Do you sell a wheel hub and bearing for this spindle?

asked by: Ted W

0

Expert Reply:

We do carry the hubs and bearings that fit spindle # LC142161. The bearing kit is part # BK1-150 which uses # L44649 for both the inner and outer bearings.

The hubs that fit come in either a 4 on 4 bolt pattern, like idler hub # AKIHUB-440-2-2K, or 5 on 4-1/2 bolt pattern, like part # AKIHUB-545-2-2K. We also have the same hubs galvanized; part # AKIHUB-440-2-G-2K for the 4 on 4 and part # AKIHUB-545-2-G-2K for the 5 on 4-1/2.

There's also a hub and drum that fits if you need brakes on the trailer. Part # AKHD-545-2-2K is the hub and drum and has a 5 on 4-1/2 bolt pattern. Part # AKEBRK-2 is a set of brake assemblies to fit as well.

All of the hubs include the bearing kit as well.

expert reply by: Charles S

0

Answer 1

As far as removing your current spindle, you will need to grind/drill off the old one. One the old spindle is removed, I recommend the BT8 Spindle for 2,000-lb Trailer Axles #TRU59FR (for a 1-3/8 diameter) or the #TRU94FR (for 1-1/4 diameter). The…

view full answer...

Answer 2

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Trailer Wheel Hub to Match 2,200 Pound Lippert Spindle

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching