Fuse Types and Amperage Values for Curt T-Connector Vehicle Wiring Harness C56291

Question

Question:

Did not install fuse when I originally installed hitch and harness...now it’s missing I lost it what size/type do I ask for at the auto parts store?

asked by: Keith R

0

Expert Reply:

Curt T-Connector Vehicle Wiring Harness # C56291 includes both a red 10-amp mini blade fuse for the red fuse holder on the harness and a pink 30-amp box fuse for the fuse box in the engine compartment. Both fuses are shown in the linked photo. You'll have no trouble finding these at your local auto parts store.

expert reply by: Adam R

0

click to enlarge

Answer 1

Hello Charles. I just checked with my contact at Curt and I was told that the Curt T-Connector #C68JR uses a 15 amp max fuse.

view full answer...

Answer 2

Using Loctite when installing a trailer hitch is not required but it can certainly be used to create an even stronger bond. Blue Loctite like the Blue Stick #LT37643 is plenty sufficient for this application. As long as the hardware for your hitch is…

view full answer...

Answer 3

Yes, trailer wiring harness #C56332 does have a fuse in a red holder near the large black converter box. If that fuse is fine, then use the vehicle owner's manual to find any fuses related to tow package wiring on the vehicle to check them. If…

view full answer...

Answer 4

To protect the 12 volt accessory power supply circuit, we recommend using a 40 amp inline circuit breaker, part number 9510.

view full answer...

Answer 5

If you are installing a 7-way and brake controller you will want to use a circuit breaker in-line when connecting the Black wire from the 7-way to the battery and in-line from the brake controller to the battery. The Black wire will draw 12 volt…

view full answer...

Answer 6

To wire the 4 clearance lights #MCL0040ABB, license plate light #M298C, and tail lights #STL190RB to your 12' long 75" wide vintage trailer, I recommend starting the 4-Way Wishbone Trailer Wiring Harness with 42" Ground Wire #A40W42B…

view full answer...

Answer 7

The #RED44FR is the 331-EBRH-ACCV3, which is the 3rd version of the Redarc Tow Pro Elite controller that was originally only available in Australia; the #331-EBRH-ACCV2 is the 2nd version and has been phased out. They're really mostly the same…

view full answer...

Answer 8

I have attached a few photos for you with all the dimensions we have for the Ark Drop Down Corner RV Stabilizer Jacks part #AR34FR. That said, Ark is an Australian company so the measurements are in metric, millimeter to be specific so you may need…

view full answer...

Answer 9

I have attached for you below a photo with the dimensions of the weld-on plate for the Ark Drop Down Corner RV Stabilizer Jack Kit part #ARK94FR. The plates are 117mm long x 72.50mm wide or 4.6" long x 2.8" wide.

view full answer...

Answer 10

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 11

I have exactly what you need to install a 7-way trailer connector on your 2015 Jeep Wrangler Unlimited. It sounds like you have the factory tow package therefore, all you would need to do is remove the 4-way you have now and replace it with the…

view full answer...

Answer 12

The Adapter 4 Pole to 6 Pole and 4 Pole Trailer Wiring Adapter #37175 has 10 gauge wire for the blue wire, red wire, and black wire. The aux circuit you mentioned would be the black wire.

view full answer...

Fuse Types and Amperage Values for Curt T-Connector Vehicle Wiring Harness C56291

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching