Measuring for Solera Awning Installation

Question

Question:

Does the size advertised on a Solera awning the center to center distance of the mounting hardware for the arms that attach to the trailer?

asked by: Frank T

0

Expert Reply:

The Solera awnings like the Solera Smart Arm 12V Power RV Awning - 16' Wide - Programmable - White Fade # LC405492 will be 16 foot center arm to center arm. This awning has the actual canopy of 15 foot 1 inch wide and then you have some roller rail on each side then the arm assembly as well. I've attached the diagram from the installation instructions that show the actual width to the center of each arm being what they state is the 16 feet, but I would definitely measure for precision before drilling holes to install.

expert reply by: Jason S

0

click to enlarge

Answer 1

Thank you for the photos! To replace your old Lippert (LCI) slam latch you can use the Lippert Standard Baggage Door Latch Kit - Black #LC317649, which is going to be the same size as your old slam latch and will fit perfectly in the existing cutout…

view full answer...

Answer 2

Are you sure that's the part number? I wasn't able to find any reference to that. Can you see a brand on the motor?

view full answer...

Answer 3

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

view full answer...

Answer 4

The #LC266149 is designed to work with Solera awnings that were manufactured before 2014, where the #LC373566 is designed for awnings built after 2015. Yes, the main noticeable difference is going to be the plug, but that directly effects how it is…

view full answer...

Answer 5

Both the Jensen JWM6A and the current model, part #JWM62A are classified as double-DIN head units, which will both use the same sized rough openings in a vehicle dash. The old #JWM6A and the current model #JWM62A both use the same pigtail, as you can…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...