Recommended Replacement Axle for 2002 Coleman Westlake Pop-Up Camper with Lifted Ground Clearance

Question

Question:

Hello, I have a 2002 Coleman Westlake pop up camper. I want to do the axle flip to get additional ground clearance and higher ride height. I know you sell kits to accomplish this. What I really want is to purchase a new axle with electric brakes and the leaf spring supports already welded on top so I can just install it when it arrives. Can you offer this product or modify an existing assembly prior to shipping it to me? Thanks!

asked by: Ryan T

0

Expert Reply:

We do not have the thru-axles with the flipped leaf spring mounts already attached. My recommendation is to use the Trailer Axle w/ Electric Brakes - EZ-Lube - 5 on 4-1/2 Bolt Pattern - 89" - 3,500 lbs # e43SR if your spring centers are 74 inches and then use the Dexter Trailer Springs Over-Under Conversion Kit # K71-384-00.

If you have different spring dimensions then I instead recommend the Timbren Axle-Less Trailer Suspension System - 4" Lift Spindle - Regular Tires - 3,500 lbs # ASR3500S06 which will give you the height you desire and will replace your leaf spring system. This will require a 2 inch square tube (not included) for the integrated holes that is cut to your custom length. Then you can add the brake assemblies # AKEBRK-35-SA and hubs # AKHD-655-35-EZ-K.

expert reply by: Jason S

0

Answer 1

The over-under conversion kit you need for your Coleman pop-up is part #K71-384-00. The difference you said you measured is a minimal amount and the #K71-384-00 will work just fine for you. If you have the VIN for the camper you can contact the…

view full answer...

Answer 2

We cannot move the spring seats here on our 89 inch axles like the #e95SR that you referenced and we only have options that are spaced 74 inches apart like this one. In order for you be able to use this axle you'd have to have new ones welded on…

view full answer...

Answer 3

Yes there is! If you do not already have a 4-Pole connector on your 2005 Toyota Highlander you will need to install the Tekonsha part #118248 if you have the factory tow package or part #118413 if you do not have the factory tow package. I have…

view full answer...

Answer 4

Sounds like you have a ground issue on your trailer. Ground problems normally show up when there is more draw on a system such as when you have the running lights on and then use another function like a turn signal or brake light but can show up any…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...