Will the Curt Hitch 13028 Fit a 1966 Chevrolet C10 with Aftermarket Bumper

Question

Question:

will this 13028 fit a 66 c10 with the Barden step bumper? I measured exactly 4 1/2 inches from bottom of truck frame to bottom of bumper? I see the hitch says 4 1/2, but see potentially where it could be lessnear where the receiver accepts the hitch

asked by: Matt

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you with a few measurements that will allow you to see if the receiver tube will clear the bumper. If it does not then please let me know and I will see if we have a better fit for you.

expert reply by: Conner L

0

click to enlarge

Matt

1/16/2019

will this 13028 fit a 66 c10 with the Barden step bumper? I measured exactly 4 1/2 inches from bottom of truck frame to bottom of bumper? I see the hitch says 4 1/2, but see potentially where it could be lessnear where the receiver accepts the hitch

Reply

Conner L.

1/16/2019

If the distance from the bottom of the frame to the bottom of the bumper is 4-1/2" exactly then I would actually use the Curt 3-Piece Trailer Hitch Receiver part # C15511 instead as the distance from the top of the receiver tube to the top of the mounting flange is right at 7-3/4" so you should have plenty of room with your Barden step bumper.

Reply

Answer 1

The hitch tube of the Curt Hitch part #13028 is going to be right at 4-1/2 inches below the frame it connects to and the opening would then be right at 7 inches forward of the rear most mounting hole. You'd have to compare that to your…

view full answer...

Answer 2

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of…

view full answer...

Answer 3

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the…

view full answer...

Answer 4

I had our warehouse measure the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #13028 you were looking at and from the crosstube to the end of the receiver measures 8" as you can see in the included diagram.

view full answer...

Answer 5

We have not had a local customer with your same truck come in for an install of this particular item so we do not have photos to share with you but we can still help you determine the position of the receiver tube once the hitch is bolted up to your…

view full answer...

Answer 6

The measurement from the top of the mounting bracket down to the top of the receiver tube measures 5 inches. Curt trailer hitch #C14082 is a custom fit hitch designed to fit the following vehicles: 1973 - 2000 Chevrolet C/K Series Pickup Cab and…

view full answer...

Answer 7

I was able to obtain from Curt a chart showing key dimensions for their 3-Piece Trailer Hitch #C15511 (and other hitch models) that I linked for you. This shows that for hitch #C15511 the overall front-to-back length is just under 24-inches. The…

view full answer...

Answer 8

The correct quick splice harness needed to install a brake controller in a 20014 Ford F-350 is the part #3035-P. I attached a picture that shows how the connector of it would match what you have in your truck. This could be used as a guide or you can…

view full answer...

Answer 9

The front two mounting bolt holes are 3 inches apart on the Draw-Tite Ultra Frame Trailer Hitch Receiver #41943, and 16-1/4 inches from the front mounting hole to the furthest. The height is 6 inches as well; this is only a fit for 1999-2021 Ford…

view full answer...

Answer 10

The drop of the B & W Class V #BWHDRH25198 is 7-3/8 inches. That represents the distance from the underside of the frame member where the hitch mounts to the top of the receiver tube. If that isn't sufficient to clear your bumper, the Curt…

view full answer...

Answer 11

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting bracket…

view full answer...

Answer 12

I spoke with my contact at Curt and he put together a chart that has all of the dimensions of the hitches you referenced.

view full answer...

Will the Curt Hitch 13028 Fit a 1966 Chevrolet C10 with Aftermarket Bumper

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching