Dimensions of Hitch Opening of Curt Hitch #13028

Question

Question:

How far does the receiver protrude past a standard bumper and how far below the license plate on a 1973 Chevy K10 shortbed stepside? I am looking for about 1inch under the license plate and protrude 1inch past it. Is that possible?

asked by: Michael C

0

Expert Reply:

The hitch tube of the Curt Hitch part # 13028 is going to be right at 4-1/2 inches below the frame it connects to and the opening would then be right at 7 inches forward of the rear most mounting hole. You'd have to compare that to your vehicle to determine where that would place the hitch opening relative to your vehicle.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...

Answer 2

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 3

I had our warehouse measure the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #13028 you were looking at and from the crosstube to the end of the receiver measures 8" as you can see in the included diagram.

view full answer...

Answer 4

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 5

The measurement from the top of the mounting bracket down to the top of the receiver tube measures 5 inches. Curt trailer hitch #C14082 is a custom fit hitch designed to fit the following vehicles: 1973 - 2000 Chevrolet C/K Series Pickup Cab and…

view full answer...

Answer 6

Actually several of your pictures did make it through! What you have there is the standard/step bumper on your 1979 Chevy C-10. Deep drop bumpers, also called cowboy bumpers, drop way down. If your truck has an 8 foot bed you can use Curt trailer…

view full answer...

Answer 7

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 8

For your 1990 Chevy K1500 with a standard/step bumper the Curt Hitch part #13028 would be a great option. It will be mainly out of sight as only the hitch opening will hang below the bumper so it would be what you are looking for.

view full answer...

Answer 9

The Curt Trailer Hitch Receiver part #13028 is designed to fit the following vechiles: - 88-91 CHEVY/GMC 4 DR CREW CAB ONLY - 73-79 FORD 250 CREW CAB - 73-06 CHEVY/GMC FULL SIZE CAB & CHASSIS w 34" FRAME - 73-06 FORD PICKUP: CAB AND CHASSIS…

view full answer...

Answer 10

I went out to the warehouse and took some measurements for the Curt Trailer Hitch Receiver item #13028 you referenced. The measurement running from the middle of the bolt holes across the length of the receiver is 31-1/8". I can confirm that…

view full answer...

Answer 11

The Draw Tite Class III hitch part #75033 that you referenced does fit your 1989 Chevy K1500 with the 37 inch frame dimension and step bumper.

view full answer...

Answer 12

I spoke to my contact at Curt about the Curt Trailer Hitch Receiver part #C14082 for your 1986 Chevrolet C/K Series Pickup and they informed me that as long as the spare tire is of the stock tire size then it will work with the hitch installed. If…

view full answer...

Dimensions of Hitch Opening of Curt Hitch #13028

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching