Mounting Bolt Spacing of Draw-Tite Hitch 41943

Question

Question:

Hi, Do you have the mounting bolt spacing? or total lenght of the flange? And what is the hitch height from the mounting surface? Thanks

asked by: Eric

0

Expert Reply:

The front two mounting bolt holes are 3 inches apart on the Draw-Tite Ultra Frame Trailer Hitch Receiver # 41943, and 16-1/4 inches from the front mounting hole to the furthest. The height is 6 inches as well; this is only a fit for 1999-2021 Ford F-350, F-450, and F-550 Cab and Chassis trucks.

expert reply by: Kyle S

0

Answer 1

I was able to obtain from Curt a chart showing key dimensions for their 3-Piece Trailer Hitch #C15511 (and other hitch models) that I linked for you. This shows that for hitch #C15511 the overall front-to-back length is just under 24-inches. The…

view full answer...

Answer 2

The correct quick splice harness needed to install a brake controller in a 20014 Ford F-350 is the part #3035-P. I attached a picture that shows how the connector of it would match what you have in your truck. This could be used as a guide or you…

view full answer...

Answer 3

I do have an option for you but I cannot recommend you add any spacers in between the trailer hitch and trailer frame as this would affect the integrity of the trailer hitch. Therefore, if the Curt Trailer Hitch Receiver part #13028 does not clear…

view full answer...

Answer 4

Because the mounting flange of the Curt #C15511 Class V hitch has 3 tabs on each side, rather than a continuous mounting flange like many other hitches, it'll fit around the rivet shown in your photo. However, be aware that the Curt #C15511…

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C15445 which is a fit for a Ford F-Series Cab and Chassis has a drop of 5-1/2" when measuring from the top of the mounting flange or bottom of the frame to the top cross tube. I have attached a photo of…

view full answer...

Answer 6

The 2017 GMC Sierra 3500 cab-and-chassis is a confirmed fit for the Draw-Tite Ultra Frame Trailer Hitch #41947 so long as the truck frame width dimension is 34-inches from outside edge to outside edge. This frame dimension requirement applies to all…

view full answer...

Answer 7

The drop of the B & W Class V #BWHDRH25198 is 7-3/8 inches. That represents the distance from the underside of the frame member where the hitch mounts to the top of the receiver tube. If that isn't sufficient to clear your bumper, the Curt…

view full answer...

Answer 8

The Curt Trailer Hitch Receiver part #13028 could potentially fit your 1966 Chevrolet C10 with aftermarket bumper. However, I would not be able to confirm this as the trailer hitch is only tested with the OEM bumper. I have attached a photo for you…

view full answer...

Answer 9

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting bracket…

view full answer...

Answer 10

I spoke with my contact at Curt and he put together a chart that has all of the dimensions of the hitches you referenced.

view full answer...

Answer 11

That's a really good question, and the reason the Curt 3-Piece Trailer Hitch Receiver - Multi Fit #C15511 is able to fit both 34 inch and 37-1/2 inch frames on your 1993 Ford is due to the placement of the side plates. If you take a look of the…

view full answer...

Answer 12

The Curt Trailer Hitch Receiver #C15809 that you referenced will work on your 2012 Dodge Ram 2500 Mega Cab. Cab and chassis model trucks come from the factory without truck beds on them at all. Typically trucks are bought like this so a flat-bed or…

view full answer...

Mounting Bolt Spacing of Draw-Tite Hitch 41943

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching