Will Pro Series Round, Snap-Ring Swivel Trailer Jack, # PS1400300303 Fit a 3 x 3 Trailer Frame

Question

Question:

My Trailer tongue is 3inch x 3. Will this trailer jack bolt on without any problems? Can you provide me with the measurements Center to Center. Also if this will not work can you recommend something that will? Thank you

asked by: Dan D

0

Expert Reply:

I went out o the warehouse to verify the measurements on the Pro Series Round, Snap-Ring Swivel Trailer Jack, # PS1400300303. It will fit either a 3 inch by 3 inch tall or a 3 inch by 4 inch tall trailer frame. I have made a picture showing the measurements of the bolt holes for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Pro Series Round Snap-Ring Jack, #PS1400300303, will bolt around your 2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a photo showing the…

view full answer...

Answer 2

The Pro Series Swivel Jack #PS1400300303 that you referenced should fit fine in your application. In the picture of the jack that I have provided has the measurements indicated. From the center of the mounting bracket to the foot plate is 11 inches.…

view full answer...

Answer 3

I went out to the warehouse and pulled the 2 jacks that would most likely fit and meet the needs of your application. First, I measured the Pro Series Round, Snap-Ring Swivel Jack, #PS1400300303, that you have referenced. This jack has a bolt hole…

view full answer...

Answer 4

Sounds like you have a round tongue trailer that has a mounting bracket welded on it for a jack that match up with the mounting bracket of the part #PS1400300303 that you referenced. Normally we don't have a solution for round tube tongues aside…

view full answer...

Answer 5

The Bulldog Topwind Jack part #BD151464 has 15 inches of travel and attaches to the trailer frame like the Pro Series you mentioned so it would be a perfect option. I attached an install video for more info as well.

view full answer...

Answer 6

The shortest we have is about 13 inches from the bracket to the top of either the jack or the handle like the Pro Series Round, A-Frame Jack #PSRV20000103. Another option, since you may not get the clearance you want, is to switch to a side mount…

view full answer...

Answer 7

Pro Series Round, Snap-Ring Swivel Trailer Jack will fit trailer frame members up to 4 tall and 3 wide.

view full answer...

Answer 8

The #PSEA20000103 is one of the shortest A-frame jacks we offer from the mounting bracket to the top of the jack at 11 inches. The best solution I can recommend would be to go with a side mounted trailer jack like part #PS1400300303 that would…

view full answer...

Answer 9

If your landing gear leg (inner or outer leg) is bent then I strongly advise replacing it. A bent leg can be an indication of other unseen damage. We have numerous replacement legs available for both the lead leg and the follower leg. But it depends…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Will Pro Series Round, Snap-Ring Swivel Trailer Jack, # PS1400300303 Fit a 3 x 3 Trailer Frame

Product Page this Question was Asked From

Continue Researching