Bolt On Top Wind Jack Recommendation for Trailer with 15 inches of Travel

Question

Question:

I am looking for a top wind jack just like the Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10inch Lift - 2,000 lbs except with about 15inch Lift. I see several models that are 15inch lift but I dont see one that is bolt on. Thank you,

asked by: Jay P

0

Expert Reply:

The Bulldog Topwind Jack part # BD151464 has 15 inches of travel and attaches to the trailer frame like the Pro Series you mentioned so it would be a perfect option. I attached an install video for more info as well.

expert reply by: Jameson C

0

Answer 1

Sounds like you have a round tongue trailer that has a mounting bracket welded on it for a jack that match up with the mounting bracket of the part #PS1400300303 that you referenced. Normally we don't have a solution for round tube tongues aside…

view full answer...

Answer 2

I went out o the warehouse to verify the measurements on the Pro Series Round, Snap-Ring Swivel Trailer Jack, #PS1400300303. It will fit either a 3 inch by 3 inch tall or a 3 inch by 4 inch tall trailer frame. I have made a picture showing the…

view full answer...

Answer 3

I went out to the warehouse and pulled the 2 jacks that would most likely fit and meet the needs of your application. First, I measured the Pro Series Round, Snap-Ring Swivel Jack, #PS1400300303, that you have referenced. This jack has a bolt hole…

view full answer...

Answer 4

The Pro Series Round Snap-Ring Jack, #PS1400300303, will bolt around your 2 inch trailer tongue. This jack can bolt to frames up to 3 inches wide by 4 inches tall and will have no problem fitting on your trailer. I have attached a photo showing the…

view full answer...

Answer 5

The Pro Series Swivel Jack #PS1400300303 that you referenced should fit fine in your application. In the picture of the jack that I have provided has the measurements indicated. From the center of the mounting bracket to the foot plate is 11 inches.…

view full answer...

Answer 6

Pro Series Round, Snap-Ring Swivel Trailer Jack will fit trailer frame members up to 4 tall and 3 wide.

view full answer...

Answer 7

The #PSEA20000103 is one of the shortest A-frame jacks we offer from the mounting bracket to the top of the jack at 11 inches. The best solution I can recommend would be to go with a side mounted trailer jack like part #PS1400300303 that would…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Bolt On Top Wind Jack Recommendation for Trailer with 15 inches of Travel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching