Looking for a Bolt-On Jack That is Less Than 11 Inches When Attached
Question:
The distance between the bottom of the three inch square rail I want to attach the jack to and the floor is 11inches. Is that enough clearance for the base plate to reach the vertical position? If I have not been clear I can send a picture.
asked by: Freling S
Expert Reply:
The Pro Series Swivel Jack # PS1400300303 that you referenced should fit fine in your application. In the picture of the jack that I have provided has the measurements indicated. From the center of the mounting bracket to the foot plate is 11 inches. If you measure from the center of your frame to the ground you will see that you will actually have about 1-1/2 inches of clearance.
I have also attached a short video with the measurements listed as well.
Product Page this Question was Asked From
Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Topwind Jack
- 10 Inch Lift
- Bolt-On
- With Rectangle Foot
- Pro Series
more information >
Continue Researching
- Shop: Pro Series Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Search Results: ball mount with 2 receiver
- Q&A: Will the Pro Series Round Snap-Ring Swivel Jack Bolt on a 2 Inch Trailer Tongue
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs
- Q&A: Is Mounting Hardware Included with Pro Series 2K Swivel Trailer Jack
- Shop: Ventline Vanair Trailer Roof Vent w/ 12V Fan - 6-1/4" Diameter - Smoke
- Search Results: trailer jack
- Shop: Trailer Valet JXS Drill Powered Swivel Trailer Jack w/ Footplate - Sidewind - 14" Lift - 5K
- Shop: Bulldog Round, Snap-Ring Swivel Jack - Bolt On - Topwind - 10" Lift - 2,000 lbs
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 5 - Pre Greased
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJD-5000 Review
- Video: etrailer Trailer Jack - Side Frame Mount Jack - TJP-5001S-B Review
- Shop: Curt Round A-Frame Trailer Jack - Topwind - 14" Lift - 2,000 lbs
- Q&A: Pro Series Ring Swivel Jack Trailer Accommodation
- Q&A: Will Pro Series Round, Snap-Ring Swivel Trailer Jack, # PS1400300303 Fit a 3 x 3 Trailer Frame
- Q&A: Recommendation for a 2,000 Pound Capcity or Higher Snap-Ring Swivel Trailer Jack
- Video: Trailer Valet JXS Trailer Jack with Footplate Review
- Video: Review of Trailer Valet Trailer Jack - JXS Side Mount Sidewind Trailer Jack - TV64FR
- Video: Pro Series Trailer Jack - Side Frame Mount Jack - PS1401040303 Review
- Search Results: a~frame trailer jack
- Q&A: Recommended 2000 lbs. Trailer Jack to Allow the Most Clearance
- Q&A: Bolt On Top Wind Jack Recommendation for Trailer with 15 inches of Travel
- Search Results: trailer jack footplate
- Video: Review of Curt Trailer Jack - A-Frame Jack - C28200
- Video: etrailer and Ram Jacks Footplate Replacement Review
- Search Results: led license plate light and bracket
- Search Results: break away system
- Shop: RV Roof Membrane
- Search Results: bulldog trailer jack