Can a Trailer Hitch Be Installed on a 1997 Mercury Sable by a Mechanic

Question

Question:

The cost and can a machanic install it. Weight capacity approximately. 3500 pounds.

asked by: Anna S

0

Expert Reply:

I recommend the Curt Class II 1-1/4 Inch Hitch, part # C12232, for your 1997 Mercury Sable. This hitch has a maximum gross trailer weight capacity of 3,500 lbs and a tongue weight capacity of 300 lbs.

You will need the recommended ball mount, part # C45522 and will also need a hitch ball like the Tow Ready 2 Inch Hitch Ball, part # 19258, For a wiring harness, you will use the # C55343 if you have a Wagon and # HM40565 if you have a sedan. I am including a link to the installation instructions on the wiring harnesses.

Anybody with average mechanical ability can install the hitch to your vehicle. I am including a link to the installation instructions on the hitch to show you how simple it is to install. The cost for installation will vary by where you are located. You will need to call a local auto repair shop to get a quote.

expert reply by: Jeff D

0

Answer 1

Yes, the Curt Trailer Hitch Receiver #C12232 is compatible with your 2001 Mercury Sable station wagon as well as the sedans. This will only fit on models with the single passenger side exit exhaust. If you have a dual exhaust you will not be able to…

view full answer...

Answer 2

I spoke with my contact at the manufacturer to make sure there were no issues with the factory dual exhaust on the 1998 Sable and found that you should have no trouble installing the hitch on your vehicle. You will need to temporarily lower the rear…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 11

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...