Assembly of Roadmaster Tow Dolly part # RM-2000-1

Question

Question:

Is there assembly of this tow dolly available??

asked by: Bob S

0

Expert Reply:

I attached install instructions for the Roadmaster Tow Dolly part # RM-2050-1 that you referenced which has a section on assembly. I attached a diagram I took from the instructions that shows how it all comes together as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes - 4,380 lbs #RM-2000-1 has the advantage of the turning wheels as opposed to the #RM-2050-1. The turning wheels on the dolly allow the dolly and vehicle to better track with the…

view full answer...

Answer 2

I spoke with my contact at Roadmaster and he said it sounds like you need to do an alignment on your Tow Dolly part #RM-2050-1. He said it sounds like the setup is toe-out and needs to be corrected. I attached a picture that I took from the attached…

view full answer...

Answer 3

You will want the Replacement Passenger Side Fender for Roadmaster Tow Dolly 2000-1, #RM-921003, for your Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes - 4,380 lbs #RM-2050-1. The Replacement Driver's Side Fender for…

view full answer...

Answer 4

Typically, the tow dolly will have a set of lights on the fenders so you will not need to wire up your vehicle for this in addition to that. If your dolly system does not already have lights we offer magnetic towing lights #TL21RK or you could wire…

view full answer...

Answer 5

The highest capacity trailer tire we offer that fits a 14 inch trailer rim is the Load Range D part #TTWTRTM2157514D which has a capacity of 2,200-lb max load at 65 psi. With trailer tires you have to keep them inflated to their max psi at all times…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

There are a number of factors involved when converting a semi 7-way to an RV 7-way. Semis generally use a 7-pin round pin socket, similar to #PK11720. And RV style 7-way uses blades, like #PK12706. We do not offer any pre-made adapters to make this…

view full answer...