Why Would Roadmaster Tow Dolly RM-2000-1 Wear Out Insides of Tire

Question

Question:

Having issues with car dolly wearing out the inside of both tires. Air pressure and wheel bearings seem good. Is there an adjustment for cast and camber on roadmaster car dollies? 2 sets of tires in one wear is too much..thanks for any input and advice ahead of time.

asked by: Eric L

0

Expert Reply:

I spoke with my contact at Roadmaster and he said it sounds like you need to do an alignment on your Tow Dolly part # RM-2050-1. He said it sounds like the setup is toe-out and needs to be corrected.

I attached a picture that I took from the attached install instructions link that details how to perform the alignment on the dolly.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes - 4,380 lbs #RM-2000-1 has the advantage of the turning wheels as opposed to the #RM-2050-1. The turning wheels on the dolly allow the dolly and vehicle to better track with the…

view full answer...

Answer 2

When towing a front wheel drive car on a tow dolly like the RoadMaster Tow Dolly #RM-2050-1 you want to put the transmission in park, secure the wheels with the wheel nets, and be sure to have the emergency brake OFF prior to towing. You will want to…

view full answer...

Answer 3

I attached install instructions for the Roadmaster Tow Dolly part #RM-2050-1 that you referenced which has a section on assembly. I attached a diagram I took from the instructions that shows how it all comes together as well.

view full answer...

Answer 4

Some tow dollies like the Roadmaster Tow Dolly part #RM-2050-1 come with a license plate bracket. If the 2020 Master Tow Dolly did not come with a license plate bracket then you can use Trailer License Plate Mount Bracket part #LPL55CB. You will…

view full answer...

Answer 5

You will want the Replacement Passenger Side Fender for Roadmaster Tow Dolly 2000-1, #RM-921003, for your Roadmaster Tow Dolly with Self-Steering Wheels and Electric Brakes - 4,380 lbs #RM-2050-1. The Replacement Driver's Side Fender for…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...