Gooseneck Hitch Adapter for Truck with Rails a B&W Patriot Hitch Fit

Question

Question:

Do they make a goose neck hitch for the Patriot rail

asked by: Kirk J

0

Expert Reply:

If you had a fifth wheel rail kit installed in the bed of your truck that the B and W Patriot hitch part # BWRVK3255 fit we have the Curt Spyder adapter part # 16085 will fit the rails and give you a gooseneck hitch ball in the bed of your truck. Reason being that the Patriot hitch is designed to fit the industry standard fifth wheel rails that most hitches out there are designed to fit. This is what the Spyder is also designed to fit too.

expert reply by: Jameson C

0

Mike

4/27/2024

If you add the 16085 to the patriot, what is it now rated for? If you add the 30,000 lb plate C35HR, what is the rating?

Reply

Jameson C.

4/29/2024

@Mike Both of the gooseneck adapters part # 16085 and # C35HR would replace the Patriot fifth wheel hitch and fit into the same rails. The capacities would be 25 and 30k respectively as they become the capacity of the rails.

Reply

Answer 1

B&W offers a replacement slider unit for the Patriot 5th wheel hitch, part #BWRVB3270. You'd simply remove the hitch head from the current stationary model and install it on the slider. This being said, the problem comes in when you try to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...