What Light Works with the Trailer Light Mounting Bracket Part # BK70BB

Question

Question:

Can you reccomend lights and a pigtail and grommet that will work with bracket BK70BB?

asked by: Robert

0

Expert Reply:

Yes, for the Trailer Light Mounting Bracket part # BK70BB you can use part # ST70RB (incandescent) or part # STL22RB (LED) for the light, part # A70GB for the grommet, and part # A45PB for the wiring harness.

expert reply by: Conner L

0

Answer 1

You'd have to drill a pretty large hole to fit the plug ends of the #98174LED through the brackets. I'd rather recommend you zip tie the harness to a much smaller hole instead of drilling the roughly 1-1/4 inch hole you'd have to drill,…

view full answer...

Answer 2

I found the review pictures you mentioned for the Thule EasyFold XT part #TH903202 that used the #BK70BB for taillights. The clamps used in the picture are the part #RE47FR. We sell wire loom too by the foot with part #459075-1. For an LED Taillight…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

What Light Works with the Trailer Light Mounting Bracket Part # BK70BB

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching