Wedge for Curt E16 for Turning Point

Question

Question:

I recently bought the Curt 16115 hitch from etrailer and am using it with the lippert turning point hitch. Is this hitch satisfactory to use with the turning point pinbox? Is the universal wedge that comes with the turning point pinbox work ok with the hitch or do you recommend a custom wedge that would be a better fit for the 16115 hitch?

asked by: Guy B

0

Expert Reply:

Though the Sidewinder Wedge for Curt E16 # C16991 is not made for a Lippert Turning Point, we have had customers successfully use the wedge with the Turning Point so it will work with your Curt E16 # C16115.

expert reply by: Kyle S

0

Answer 1

Congrats on all your new toys! I do not think a Curt 5th wheel hitch, like item #C16120, is the best for your set up. You would need to purchase an adapter rail item #C88KR to use this hitch with your puck system. This adds weight, cost, and…

view full answer...

Answer 2

If you have the 13K Demco Autoslider #DM8550040 that installs on industry standard base rails, like part #RP50087-58, then yes, the Demco Recon #DM8550043 will fit in the 5-1/2' bed of your 2015 Ford F-150. As far as compatibility with the…

view full answer...

Answer 3

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 4

Yes. There will be a large amount of torque in this case since Sidewinder pin boxes (or your Lippert Turning Point) pivot and twist in a different way from standard pin boxes they require fifth wheel hitches to be attached to the truck in four points…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 9

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...