How Much Does the Curt Trailer Hitch Receiver # C13377 Weigh

Question

Question:

What is the weight of the hitch

asked by: Dpug

0

Expert Reply:

The Curt Trailer Hitch Receiver # C13377 has a shipping weight of 36 lbs so after you take off the packaging it will weight 30 lbs.

It does have a max gross trailer weight rating of 3,500 lbs and a max tongue weight rating of 525 lbs. This trailer hitch is confirmed to fit a 2017 - 2018 Nissan Rogue Sport.

expert reply by: Jon G

0

Answer 1

The Torque Specification is found in the installation instructions on our product page on the etrailer #e98846 receiver hitch. A Torque Wrench #PT87ZR would be the type that you would need to achieve that rating.

view full answer...

Answer 2

Good question, though the construction of the Curt hitch for your 2019 Nissan Rogue Sport won't affect its ability to carry your bike racks and four bikes. the Curt #C13377 hitch has a tongue weight capacity of 525 lbs, which is well over the 200…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #C13377 and the etrailer Trailer Hitch Receiver part #e79YR which are the two trailer hitch options for your 2019 Nissan Rogue Sport have the same ground clearance measurement. This ground clearance measurement…

view full answer...

Answer 4

All three hitches are compatible with your vehicle. If the install procedure and how the hitches fit on the vehicle are compared, the etrailer #e98846, Draw-Tite #75902 and Curt #C13204 are for the most part identical. The Curt and the Draw-Tite…

view full answer...

Answer 5

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

How Much Does the Curt Trailer Hitch Receiver # C13377 Weigh

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching