Could Brophy Camper Scissor Steps AS23 Mount on Truck Tailgate

Question

Question:

Could these steps be installed directly to the tailgate of my pickup? The camper sits on the tailgate, there is enough space and clearance.

asked by: Joanne M

0

Expert Reply:

If you were willing to mount the mount bracket of the Brophy Scissor Step kit part # AS23 to your truck's tailgate yes this will fit and work well for you.

expert reply by: Jameson C

0

Answer 1

I went to the warehouse and pulled one of the Aluminum Scissor Steps, part #AS23 to take a measurement for you. I have attached a photo of the top mounting strip and step you can check out. The distance from the mounting strip on the step assembly to…

view full answer...

Answer 2

The Brophy Camper Scissor Steps - 4 Steps - Aluminum - Non-Slip Tread - 24" Wide - 300 lbs #AS24 will work well for your Lance 650 Camper as long as the height to your threshold is between 31 and 39 inches. If it is between 24 and 30 inches…

view full answer...

Answer 3

The mounting bracket for the Brophy Camper Scissor Steps #AS23 is 24 inches long and has 5 mounting holes spaced 5-1/4 inches apart. The end mounting holes are 1-1/2 inches from each side. Also, each angle is 1 inch wide. If you're looking for…

view full answer...

Answer 4

Sounds like you'd want to go with a removable scissor setup like the Brophy Camper Steps part #AS24 which will need to be taken off it's mounting bracket between uses. This will give you total access to your trailer hitch when needed.

view full answer...

Answer 5

The dimensions of the TorkLift GlowStep Stow N' Go Mounting Bracket #TLA7810 that you referenced is 23 inches wide by 7-1/2 inches tall. It would not need to be reinforced any further than just installing the mount.

view full answer...

Answer 6

When installing the Brophy Tailgate Scissor Step Mounting Bracket #TSSB you will first measure the distance between the two pins on the bracket, on center. Then with your tailgate open and laying flat, you will take a 5/8 inch measurement in from the…

view full answer...

Answer 7

The dimensions of the TorkLift GlowStep Stow N' Go Mounting Bracket #TLA7810 that you referenced is 23 inches wide by 7-1/2 inches tall. If the plate is partially covered I wouldn't stress too much about it. We've found that it's…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Could Brophy Camper Scissor Steps AS23 Mount on Truck Tailgate

Product Page this Question was Asked From

Continue Researching