What is Height of TorkLift GlowStep Stow N' Go Mounting Bracket # TLA7810

Question

Question:

I have a 2006 dodge ram 2500 with a Hawk pop up camper. It appears the mount would end up covering the license plate that is built into the bumper. What is the height of the mount? Any suggestions to not end up covering the license plate?

asked by: Mark

0

Expert Reply:

The dimensions of the TorkLift GlowStep Stow N' Go Mounting Bracket # TLA7810 that you referenced is 23 inches wide by 7-1/2 inches tall. If the plate is partially covered I wouldn't stress too much about it. We've found that it's almost never a problem having the plate partially covered.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The dimensions of the TorkLift GlowStep Stow N' Go Mounting Bracket #TLA7810 that you referenced is 23 inches wide by 7-1/2 inches tall. It would not need to be reinforced any further than just installing the mount.

view full answer...

Answer 2

If you were willing to mount the mount bracket of the Brophy Scissor Step kit part #AS23 to your truck's tailgate yes this will fit and work well for you.

view full answer...

Answer 3

When installing the Brophy Tailgate Scissor Step Mounting Bracket #TSSB you will first measure the distance between the two pins on the bracket, on center. Then with your tailgate open and laying flat, you will take a 5/8 inch measurement in from the…

view full answer...

Answer 4

We do offer mounting brackets for scissor steps. I have attached a photo of the Replacement Scissor Step Bracket for 18 inch steps, part #CR2001. You can check out the bracket to see if this is the style you need for mounting your scissor steps. This…

view full answer...

Answer 5

I have a solution for you but I was able to reach out to one of my contacts at TorkLift and the GlowStep Stow N' Go Mounting Bracket #TLA7810 needs to be mounted vertically, not horizontally, because of concerns with the leverage required to hold…

view full answer...

Answer 6

It is too small of a space to fit the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 4 Steps - 375lbs - Black Bracket Item #TLA7834 but you can instead mount it to the bumper of your camper like in the attached picture.

view full answer...

Answer 7

The TorkLift GlowStep Stow N' Go Mounting Bracket for Truck Bed Campers #TLA7810 measures 2-1/2" from the bottom mounting hole to the top mounting hole, and 19-1/2" across the two mounting holes. This bracket also has overall…

view full answer...

Answer 8

I spoke to TorkLift about the issue you're having with the TorkLift GlowStep Stow N' Go Scissor Steps part #TLA7834 and they informed me to inform you to tighten the hinge tension on the side that's sagging. I have attached for you below…

view full answer...

Answer 9

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Answer 10

I recommend using the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide - 375 lbs #TLA7804-8000. These are a 4 step system that has glow tape on the steps to help with visibility at night, and the adjustable landing…

view full answer...

Answer 11

I may have another option but unfortunately the Brophy Camper Scissor Steps #SS04 you have were not designed to be permanately installed and will not work with the TorkLift GlowStep Stow N' Go Mounting Bracket #TLA7820 you mentioned. The Brophy…

view full answer...

Answer 12

I confirmed with Camco that their FasTen RV Leveling Blocks #CAM44521 do not carry a maximum RV weight rating so they are compatible with virtually any RV or motorhome out there. This set is gray and the part #CAM44512 is yellow.

view full answer...

What is Height of TorkLift GlowStep Stow N' Go Mounting Bracket # TLA7810

Product Page this Question was Asked From

Continue Researching