Replacing Slipper Springs With Double-Eye Springs
Question:
So, I recently bought a boat and the trailer needs more work than I had expected. One of the issues is the back bracket that holds the slipper leaf is broken. Id like to upgrade the leafs and put bigger tires on it anyway. Is there a way to use u bolts of some kind to attach the slipper part or should I use eye to eye with new hangers? And do hangers need to be welded? Its an old Sears Gamefisher trailer. I have a 13 ft aluminum boat on it. Thanks.
asked by: Steven
Expert Reply:
There are no U-bolts to attach the slipper part, I recommend replacing your slipper springs with double eye springs. In order to do this you need to know the weight rating of your axle as well as the length from center eye to center eye so you can properly place your hangers.
For example, the 6-Leaf Double-Eye Spring # e27SR measures 26 inches from center of spring eye to center of spring eye and has a 4,500 lbs capacity; you will need to find springs that match your trailer's capacity as closely as possible.
The other thing you would need is a hanger kit such as # APS3, which has 1-1/2" tall front hangers, 1-1/4" tall rear hangers, and 3-1/8" shackle straps. The correct hanger kit will depend on the hanger size you need and the hangers are going to need to be welded on. The photo I have added should be useful to help you determine where the hangers should be welded.
I have also added a link for you to a help article on double eye suspension which I recommend checking out.
Products Referenced in This Question
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear
- Trailer Leaf Spring Suspension
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- etrailer
more information >
Product Page this Question was Asked From
6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles - 26" Long
- Trailer Leaf Springs
- Double Eye Springs
- 4500 lbs
- 1-3/4 Inch Wide
- 6 Leaf
- 26 Inch Long
- Painted
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles - 24-5/8" Long
- Shop: Trailer Wiring
- Shop: Spindle Grease Seal Set for L44643 Inner Bearing and 1.980 Bearing Buddy
- Shop: 3-Leaf Slipper Spring w/ Radius End for 1,500-lb Trailer Axles - 24-5/8" Long
- Shop: Kenda 4.80-12 Bias Trailer Tire with 12" Galvanized Wheel - 4 on 4 - Load Range C
- Video: Redline Trailer Suspension - Leaf Spring Suspension - 115706S Review
- Search Results: straight tongue trailer coupler
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Loadstar ST175/80D13 Bias Trailer Tire with 13" Galvanized Wheel - 5 on 4-1/2 - Load Range D
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: axle
- Search Results: slipper springs
- Video: Kenda Tires and Wheels - Tire with Wheel - AM30550 Review
- Search Results: galvanized hub kit
- Q&A: Grease Seal For a 1" Straight Spindle and Bearing Buddy Bearing Protectors
- Q&A: What is the Offset of a Trailer Wheel
- Video: Kenda Tires and Wheels - Tire with Wheel - AM3S160 Review
- Q&A: Replacement Leaf Springs for Harbor Freight Folding Trailer
- Search Results: trailers
- Search Results: hanger
- Search Results: 205 65 10
- Video: Kenda Tires and Wheels - Tire with Wheel - AM30670 Review
- Video: Kenda Tires and Wheels - Tire with Wheel - AM30630 Review
- Q&A: What Should the Voltage Output Be at the 4-Way Plug on Curt T-Connector Wiring Harness # 56016
- Q&A: Replacing Slipper Springs with Double-Eye Springs
- Q&A: Replacement Brake Assemblies for Escort Boat Trailer
- Q&A: Replacement Actuator Recommendation for Tie Down Engineering Model 66
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Video: Curt Class I Trailer Hitch Installation - 2020 Mazda CX-30
on Trailer Leaf Springs
