Pin Hole to Rear of Hook on Curt Pintle Hook # C48005

Question

Question:

Can you please tell me the length from the rear of the hook to the center of the hole? I’m trying to make an appropriate length receiver to weld on my truck with a special application. Therefore, I need the exact length of where the base of the hitch itself would sit against the face of the receiver to where I’d need to drill the hole to accept it. Thank you.

asked by: Mark H

1

Helpful Expert Reply:

The distance you are looking for is 5-7/8 inches on the Curt Pintle Hook # C48005 that you referenced.

expert reply by: Jameson C

1

click to enlarge

Answer 1

With utility/service beds not sitting the same way as a stock bed, we cannot guaranty the B&W #BWHDRH25600 will fit. That being said, we do still have another option available. The Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver part #C15400 and the Curt Trailer Hitch Receiver part #C15800 are the exact same trailer hitch save for one has a 2" receiver tube opening and the other a 2-1/2" receiver tube opening. The dimensional drawing…

view full answer...

Answer 3

As you obviously have already learned there are a lot of variables into building a trailer. And I can't tell you what is or isn't completely safe in your exact circumstances. I highly recommend having your setup evaluated by a professional…

view full answer...

Answer 4

Pintle hitches are made to fit certain sized Lunette rings. The rings that we carry are only available in 2-1/2" or 3" diameter sizes. For example, the Curt Pintle Hook for 2" Hitches #C48004 fits lunette ring couplers with a minimum…

view full answer...

Answer 5

The Curt Pintle Hook for 2" Hitches - 20,000 lbs, #C48004 will be at its full capacity for a 10 ton trailer, but is rated to handle it. Your 2010 Ram 3500 HD is only rated to tow 12,100 at the bumper unless you have done extensive upgrades in…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...