Recommended Gooseneck Hitch for a 2006 Ford F-450 Flatbed

Question

Question:

Hello. I have a 2006 f450 cab and chassis with a 16ft flatbed. Im wondering about what gooseneck kit I would need .

asked by: Dj

0

Expert Reply:

The best gooseneck hitch we have for your 2006 Ford F-450 Flatbed is the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks part # BWGNRK1500. This hitch has a 30,000 lb weight capacity, removable ball design, and is made right here in the U.S.A. B&W hitches are considered to be one of the best on the market which is why I recommend this hitch for you.

I have attached a review video but please keep in mind that this hitch is not a custom fit nor do we have any custom fit options for your vehicle.

expert reply by: Conner L

0

Answer 1

I have a solution for you but the B&W Turnoverball Underbed Gooseneck Trailer Hitch item #BWGNRK1116 will not fit your 2017 F-350 flatbed. That trailer hitch is installed directly on top of the frame and sticks through the bed of the standard…

view full answer...

Answer 2

Good questions, and let's start with the better brand of gooseneck for your flatbed truck (which will lead to the proper positioning), and by far the best option is the B&W, which is the following part number: - B&W Turnoverball Underbed…

view full answer...

Answer 3

B and W does make a gooseneck hitch that was designed for universal flatbed applications like yours but it does not look quite like what you have. It's the part #BWGNRK1500 which would work in place of what you have but it does not look like you…

view full answer...

Answer 4

If your 2000 Ford F-350 dually is a cab and chassis model that has a frame width of 34 inches measured from outside to outside yes the Buyers Products Hitch Plate #3371809061A would fit and work well as that's what it was designed to fit.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Another wire or harness is not needed on the 2023 Honda CR-V for the install of the Curt 4-Way Wiring Harness #C56370, but you do have to add 20 amp fuse to location #17 in the fuse box.

view full answer...

Answer 12

If your Ford F-450 has an actual bed and is not a cab and chassis model (with a service bed or flatbed) then you can use the Curt universal folding gooseneck ball rail kit #C61502. You could then use Curt hitch #C-52 or #C65500. A custom hitch for a…

view full answer...