How to Access Brake-Only Lighting Signal 2018 GMC Canyon for 3rd Brake Light Installation
Question:
I cannot figure out how to install a third brake light on my century truck cap. How do I locate the proper wire that will turn on the brake light without it flashing. Thanks for your help.
asked by: Alan G
Helpful Expert Reply:
In order to add a 3rd brake-only light to your truck cap you will use a tail light converter to separate out the brake signal from the combined brake/turn signal circuits on your Canyon.
If the truck does NOT have LED tail lights use part # 118158 or part # C56196.
These converters connect to the left and right combined stop/turn circuit wires (yellow and green, respectively). The red wire on the converter's output side delivers a brake-only lighting signal you can use for your 3rd brake light. This circuit will not blink when your turn signals are activated.
If you have a 7-way and you want to avoid cutting into the truck's wiring to obtain the combined signals you can use part # 20140. This simply plugs in at the back of your 7-way and gives you access to the left and right stop/turn signals that will be fed to the input side of the converter, to its yellow and green wires. You can use butt connectors # 05731-5.
Products Referenced in This Question
16-14 Gauge Butt Connector - 5 Pack
- Wiring
- Wire Connectors
- Butt Connectors
- 16-14 Gauge
- Deka
more information >
Vehicle to Vehicle Tail Light Converter
- Accessories and Parts
- Trailer Wiring
- Mounting Hardware
- Brackets
- 7 Round
- 7 Round
- Tow Ready
more information >
Curt 2 to 3 Wire Tail Light Converter
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal
- CURT
more information >
Product Page this Question was Asked From
Curt 2 to 3 Wire Tail Light Converter
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Optronics Load Resistor for LED Lights Installation
- Q&A: Troubleshooting Curt 2-Wire to 3-Wire Converter Installation on Trailer
- Q&A: How to Connect a Camper Shells Third Brake Light on a 2008 Chevy Silverado
- Q&A: How to Wire a Third Brake Light on a Camper Shell
- Q&A: Installing Wiring for Truck Cap Stop Light on a 2014 Chevy Silverado
- Q&A: Solution for 2020 Ram with Flat Towing Braking System that Presses Brake Pedal for Turn Signals
- Q&A: How To Stop Leer Third Brake Light from Flashing with Turn Signals
- Q&A: Separating Out a Combined Brake Light and Turn Signal to Have Separate Turn Signals and Brake Lights
- Shop: Triple LED Trailer Tail Light - Stop, Tail, Turn, Backup - Red and Clear Lens - Qty 1
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Female PL-3 Plug - Qty 1
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Pigtail - Qty 1
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Hopkins Tail Light Converter - LED Compatible
- Shop: Curt 2 to 3 Wire Tail Light Converter
- Shop: Vehicle Tow Bar Wiring
- Shop: Trailer Wiring
- Shop: Access LED Light Strip for Truck Beds - 18" Long - Battery Powered
- Search Results: brake wire gauge
- Shop: Brake Controller
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Base Plate for Tow Bar
- Video: Choosing the Right Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer hitch wiring
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: hitch
- Video: Tow Ready 4-Pole Mounting Bracket Installation