Availability of 2 inch to 1-1/4 inch Hitch Adapter for Kuat NV Bike Rack

Question

Question:

I am looking for a Class 1 1.25 inch to 2 inch Hitch adapter. I have a 2 inch Kuat NV 2 that Id like to use on my Girlfriends 2002 Honda Accord that we are putting a 1.25 inch Class 1 hitch on. Do you guys have that adapter? Thanks!

asked by: Brendan R

0

Expert Reply:

We have the 1-1/4 inch to 2 inch hitch adapter part # HTAD which is Class I hitch compatible. You should note that when you use an adapter like this you cut the tongue weight capacity of the hitch it is installed in by 50 percent.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I would recommend the CURT Trailer Hitch Anti-Rattle Kit #F-315. This anti-rattle bracket works on a 1-1/4 inch hitch and when tightened down helps to eliminate the noise and vibration of a hitch accessory inside the trailer hitch. I do not have a…

view full answer...

Answer 2

Yes, you can use a hitch adapter like this one from Brophy #HTAD which fits into a 1-1/4" hitch receiver and has a 2" receiver on the other end. If you want an adapter with a rise, there's also #HT5R which gives you a lift of 5 inches.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...