Pro Series Snap Up Handle Associated with part # 113913

Question

Question:

I have a pro series weight distribution hitch. I believe the part number is 113913. It doesnt have a handle though. What part number is the handle and where can I buy one?

asked by: Devin J

0

Expert Reply:

What you are looking for is the snap up handle # RP58162 which we have confirmed with Reese/Pro Series as being the correct handle you'd need.

The head and picture you sent in a picture of is the Pro Series RB2 part # 58333.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went ahead and confirmed with my contact at Curt that the spring bars on the Curt TruTrack 2P Weight Distribution System w/ Sway Control - 7-Hole Shank #C69JR are 35" from end to end. I went ahead and attached a diagram of this measurement for…

view full answer...

Answer 2

The difference between the two systems is basically the attachment point. One is not better than the other except that the trunnion bars are a little easier to install than the round bars that require a clip to hold them into the head. For the round…

view full answer...

Answer 3

The Reese Replacement Trunnion Spring Bar, 1200 p0unds, part #RP66009, will work if your old bars were rated at 1,200 pounds. If your old bars were rated below 1,200 pounds and are over 3 years old, part #RP66009 will not work. If you have the older…

view full answer...

Answer 4

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 5

You are not missing anything and you are correct. The Reese Weight Distribution Shank #RP69FR will provide 8.75" of drop. I have included a picture that shows the drop dimensions between each hole.

view full answer...

Answer 6

For your Pro Series weight distribution system on your 2012 Dodge Ram 3500, I recommend the Pro Series WD Shank - 14" Long - 4-3/4" or 6-1/2" Drop - 1.5K TW #RP63971. This will account for the 2-3 inches of drop you mentioned whether…

view full answer...

Answer 7

Reese doesn't offer a spring bar handle as a replacement part for the #RE44FR weight distribution kit, but luckily the Equal-i-zer #EQ95-01-6050 would work for you.

view full answer...

Answer 8

The Mighty Cord Replacement Hardwire RV Plug, part #A10-P30VP, can be used outdoors but this plug can not be exposed directly to the elements since it is not 100% waterproof. As long as there is a door or other form of protection on the power outlet…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The Mighty Cord Replacement Hardwire RV Plug part #A10-P30VP is about 4" long x 2-1/2" wide x 2-1/4" thick. This should fit inside your power cord hatch but you will need to measure to be certain.

view full answer...

Answer 11

Sounds like you are wanting to know if the Fan-Tastic Vent 3350 Series Upgrade Kit #FV803358 is the correct kit for your roof vent. Basically this is designed to fit the Fan-Tastic Roof Vents to turn it into a 3350 series of Fan-Tastic Vents like…

view full answer...

Answer 12

The #84 Spindle for 3,500-lb Trailer Axles part #TRU84FR and the Trailer Idler Hub Assembly for 3,500-lb Axles part #AKIHUB-550-35-K for a 5 on 5" wheel bolt pattern or the Trailer Idler Hub Assembly for 3,500-lb Axles part #AKIHUB-545-35-K for…

view full answer...

Pro Series Snap Up Handle Associated with part # 113913

Product Page this Question was Asked From

Continue Researching