Recommended Weight Distribution Drop Shank For 63970 Pro Series System

Question

Question:

I had an F250 2000 Super Duty and just bought a 2012 Dodge Ram 3500. It appears the Ram is taller by about 2-3 inches. It would be nice to just upgrade the system that I have and not have to buy a completely new system. Can I just change out the shank that goes into the receiver? What do I need to do to get the right part? 63970 Pro Series

asked by: Daniel C

0

Expert Reply:

For your Pro Series weight distribution system on your 2012 Dodge Ram 3500, I recommend the Pro Series WD Shank - 14" Long - 4-3/4" or 6-1/2" Drop - 1.5K TW # RP63971. This will account for the 2-3 inches of drop you mentioned whether using round bar or trunnion bars.

expert reply by: Jason S

0

Answer 1

The weight capacities of the Reese weight distribution shank part #RP69FR is the same regardless of what adjustment holes you use on it. This has a 1,200 lb tongue weight capacity.

view full answer...

Answer 2

When it comes to installing a lift kit on your 2022 Airstream 33 Foot Classic The Torflex Lift Kit - Tandem Axle - 3-1/8 inch Lift #K71-725-02 will work for you if you have a tandem axle. This system is not compatible with top-mounted axles, and is…

view full answer...

Answer 3

You are not missing anything and you are correct. The Reese Weight Distribution Shank #RP69FR will provide 8.75" of drop. I have included a picture that shows the drop dimensions between each hole.

view full answer...

Answer 4

The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of the setup when it is loaded and ready to tow. This figure also includes the weight of any cargo behind the rear axle of the tow vehicle. I…

view full answer...

Answer 5

The difference between the two systems is basically the attachment point. One is not better than the other except that the trunnion bars are a little easier to install than the round bars that require a clip to hold them into the head. For the…

view full answer...

Answer 6

If you want to just add on some sort of extension you can use Safety Chain Quick Link #C82932 which has a working load limit of 3300-lbs. This will give you about 3-inches additional length. Ideally trailer safety chains will be one continuous…

view full answer...

Answer 7

I believe we have just what you're looking for. Check out the Curt Adjustable Weight Distribution Shank #C17100. This weight distribution shank has 7 holes for adjustment, will work with 2" trailer hitches, and has a maximum weight…

view full answer...

Answer 8

I do have a solution, but I would not recommend using a hitch extender with the Patriot Hitches Adjustable Drop Hitch Receiver #PH67SR. This receiver won't reduce the capacity of your hitch, but an extender will reduce the capacity by 50%.…

view full answer...

Answer 9

That is a great question. Both of those are great weight distribution hitches. Between the two, I prefer the Reese Dual Cam II over the Strait Line. The Dual Cam uses an L-bracket to attach to the frame, instead of a chain and lift bracket.…

view full answer...

Answer 10

You are definitely on the right track here. When it comes to weight distribution hitches, it all comes down to your tongue weight. All of these systems will have a range of tongue weights that you want to stay within for them to work effectively. I…

view full answer...

Answer 11

The Replacement Lens part #A68RB that you referenced measures 3-1/2 inches long by 1-1/8 inches tall. If the lens you are looking to replace matches these dimensions then this would work for you. The part number for the light this lens is designed…

view full answer...

Recommended Weight Distribution Drop Shank For 63970 Pro Series System

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching