Ball Mount with Drop Recommendation and Hitch Opening for Bike Rack

Question

Question:

Do you make a 4 in drop hitch with a bike rack mount on the top

asked by: John M

0

Expert Reply:

The closest thing we have to what you mentioned is the Curt multi-purpose ball mount part # D210 which has a hitch opening up above for mounting a bike rack. But we do not have anything that can do a 4 inch drop as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We don't have any great hitch adapter solutions that you could use to add additional rise to the hitch setup you are using to carry your hitch mounted cargo carrier. Doing so adds quite a bit of movement to the hitch setup and cuts the capacity…

view full answer...

Answer 2

I have a solution for you, but you're correct that the Blue Ox #BX88132 is not designed for hitch mounted accessories like your cargo carrier. The only available solution that will allow you to carry up to 500-lbs is the Curt Multipurpose Ball…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hello Steve. I do have a good solution for you, but I cannot recommend using the Malone Adapter #MPG544. Since it is rated for towing only 4,000 lbs, your 8,000 lb towed vehicle would be double the max towing capacity. You are right about there being…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

We carry a very handy 2 inch ball mount for this exact application. The part is #D210. The ball mount slides and pins into your hitch and the top receiver will accept 2 inch bike racks and hold them above the ball. The Ball Mount has a 500 lb tongue…

view full answer...

Ball Mount with Drop Recommendation and Hitch Opening for Bike Rack

Product Page this Question was Asked From

Continue Researching