Mounting Brackets Recommendations for Roadmaster Reflex Steering Stabilizer for a 2000 Freightliner

Question

Question:

I have a roadmaster RSSA cylinder to mount on a 2000 Freightliner chassis under a holiday endeaver. I see on Roadmaster site it uses the rbk14. Is this correct? Thanks

asked by: Paul D

0

Expert Reply:

I checked with Roadmaster and the Custom Mounting Brackets # RM-RBK14 would be the correct bracket kit for your 2000 Freightliner to install a Roadmaster Reflex Steering Stabilizer # RM-RSSA.

expert reply by: Jameson C

0

Answer 1

The correct mounting kit for your 1996 Fleetwood Bounder Class A with a Ford F-53 chassis and V8 engine is #RM-RBK4, regardless of the motorhome's GVWR. This will include the original custom mounting brackets and all hardware that come in the…

view full answer...

Answer 2

The mounting brackets can vary depending on the chassis of the vehicle they're going on. For your 2004 Roadmaster Monaco the confirmed fit is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes #RM-RBK6-RSSA.…

view full answer...

Answer 3

In order to reduce the jolting feeling in your steering you are going to want to add a steering stabilizer like the Roadmaster Reflex Steering Stabilizer part #RM-RSSA. The Reflex Steering Stabilizer contains a tempered steel spring that will work to…

view full answer...

Answer 4

We do carry steering staiblizers for your 2001 Ford F-53 chassis RV. If you have a V8 you would need the part #RM-RBK4-RSSA which is a confirmed fit.

view full answer...

Answer 5

The two options you have for the Roadmaster Reflex Steering Stabilizer is part #RM-RBK4-RSSA for if you have a V8.

view full answer...

Answer 6

If you are having a hard time keep the steering wheel centered while driving the RV then a steering stabilizer is the way to go. If the RV is getting pushed around by wind then an anti-sway bar would be the way to go. If you want the driving…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

The torque spec for the rear U bolts on your 2019 F53 motorhome are dependent on the size. If you have 3/4 x 16 u bolts (and used a 1 1/8" socket to remove the nuts) then they torque to 250 lb-ft. If the u bolts are 7/8 x 14 (and you used a 1…

view full answer...

Answer 11

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Answer 12

According to Solara (Lippert), the correct number of turns to set the proper tension of their slide toppers like #LCV000163285 is between 12 to 16 turns, so I'd consider 14 to be a pretty good happy medium.

view full answer...

Mounting Brackets Recommendations for Roadmaster Reflex Steering Stabilizer for a 2000 Freightliner

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching