Roadmaster Steering Stabilizer Mounting Kit for 1996 Fleetwood Bounder with Ford F-53 Chassis

Question

Question:

What is the correct steering stabilizer mounting kit for a 1996 Fleetwood Bounder with on a Ford F-53 chassis with a 460 V-8 gas engine?

asked by: Thomas M

0

Expert Reply:

The correct mounting kit for your 1996 Fleetwood Bounder Class A with a Ford F-53 chassis and V8 engine is # RM-RBK4, regardless of the motorhome's GVWR. This will include the original custom mounting brackets and all hardware that come in the # RM-RBK4-RSSA kit.

I have attached the complete installation instructions for you at the bottom of the page.

expert reply by: Carla M

0

Answer 1

In order to reduce the jolting feeling in your steering you are going to want to add a steering stabilizer like the Roadmaster Reflex Steering Stabilizer part #RM-RSSA. The Reflex Steering Stabilizer contains a tempered steel spring that will work to…

view full answer...

Answer 2

The mounting brackets can vary depending on the chassis of the vehicle they're going on. For your 2004 Roadmaster Monaco the confirmed fit is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes #RM-RBK6-RSSA.…

view full answer...

Answer 3

We do carry steering staiblizers for your 2001 Ford F-53 chassis RV. If you have a V8 you would need the part #RM-RBK4-RSSA which is a confirmed fit.

view full answer...

Answer 4

If you are having a hard time keep the steering wheel centered while driving the RV then a steering stabilizer is the way to go. If the RV is getting pushed around by wind then an anti-sway bar would be the way to go. If you want the driving…

view full answer...

Answer 5

I checked with Roadmaster and the Custom Mounting Brackets #RM-RBK14 would be the correct bracket kit for your 2000 Freightliner to install a Roadmaster Reflex Steering Stabilizer #RM-RSSA.

view full answer...

Answer 6

The two options you have for the Roadmaster Reflex Steering Stabilizer is part #RM-RBK4-RSSA for if you have a V8.

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Roadmaster Steering Stabilizer Mounting Kit for 1996 Fleetwood Bounder with Ford F-53 Chassis

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching