Will Trailer Hitch from 2005 Honda Odyssey fit 2014 Odyssey

Question

Question:

will the hitch that is on my 2005 odyssey fit my 2014 odyssey

asked by: Bryan

0

Expert Reply:

Yes, a hitch from a 2005 Honda Odyssey like the Draw Tite # 75270 would fit on a 2017 model as well. Since hitch hardware is considered one-time-use though you'd need new hardware. For that we have the # RHK.

Enter the part number of the hitch you have and select the manufacturer and we'll ship you out the correct hardware.

expert reply by: Jameson C

0

Answer 1

The bolts that are used to attach a hitch like the #75270 to your 2007 Honda Odysey are M12 X 1.25 X 35mm. That means you would need a M12x1.25 size thread tap.

view full answer...

Answer 2

The size of the bolts that come with the Draw Tite hitch part #75270 that you referenced is M12 X 1.25 X 35mm. You could use a thread tap to keep the weldnuts clean but you should know that hitch hardware is considered one time use so if you pull…

view full answer...

Answer 3

The Draw-Tite Class III Round Tube Trailer Hitch Receiver, part number 75270, includes all necessary mounting hardware, as well as installation instructions. This hitch utilizes weldnuts, nuts that are welded into the frame at the factory. Before…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...