Hitch and Wiring Fits for 2004 Dodge Sprinter

Question

Question:

I have an 04 Sprinter with all Mercedes labelling. I believe it is dimensionally the same as the Dodge. Can you verify that the hitch and wiring harness? would fit? Thank you.

asked by: Tim P

0

Expert Reply:

Both of our primary hitch suppliers, Curt and Draw-Tite, show no vehicle listing for a M-B branded Sprinter for model year 2004. Only a Dodge Sprinter is listed, both 2500-series and 3500-series.

You can confirm the correct hitch based on the van's wheelbase and drivetrain. If you click on the "Select Vehicle Style" drop-down menu tool at the top of the linked page you can select your Sprinter's configuration; you will then see the hitches just for that setup.

For example, for a 118-inch wheelbase with single rear wheels you can use Curt Class IV hitch # 14250 or Class III hitch # 13250. For this version that does not have a factory 7-way harness the 4-pole wiring kit is # C59496.

expert reply by: Adam R

0

click to enlarge

Answer 1

Yes, we have the Draw Tite hitch part #75210 as a confirmed fit for your 2004 Freightliner Sprinter 2500 that has the factory step bumper. Draw Tite states that on vehicles with factory step bumper, bumper mounting brackets will be re-attached at…

view full answer...

Answer 2

The spare tire retainer would almost certainly interfere with installing the #75210, but we do have a hitch that is positioned a bit differently so it would fit perfectly. The Curt #13250 class III hitch will avoid the spare tire retainer, as shown…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Thanks for the question Mike; the answer is yes, the 15,000 Btu Advent Air Low Profile RV Air Conditioner - Black #ADV56FR and White #ADV29FR do indeed work with your Dometic set up.

view full answer...

Hitch and Wiring Fits for 2004 Dodge Sprinter

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching