Wrentch for Curt Hitch Ball # A-82

Question

Question:

What size wrench or socket is needed to tighten the hitch nut please.

asked by: Matthew T

0

Expert Reply:

For 2" Curt hitch ball # A-82 you want to use Curt 6-Point Hex Wrench for Trailer Hitch Balls with 3/4" or 1" Diameter Shanks # C20001 and use the 1-1/8" end.

I've added a link to a video review of the wrench for you to check out.

expert reply by: Kyle S

0

Answer 1

Tightening a ball to a ball mount does require a substantial amount of foot pounds of torque. The lock washer puts further tension on it. What you can do is put the ball mount in the shank side ways and use a special wrench for the large nut to get…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 8

The TireMinder i10 TPMS #TM38FR refreshes every 6 seconds. You will get a visual and audible alert when the monitor receives the signal from your tire sensor is either below your pressure or the temperature exceeds the maximum setting.

view full answer...

Answer 9

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 10

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 11

I attached a picture that shows how much of the etrailer.com hitch part #E98901 would hang below the rear bumper when installed.

view full answer...

Answer 12

In order to wire your cargo trailer for both 12 volt DC and 110 volt AC power you would need to install a AC/DC distribution panel and power converter which we currently do not offer. You would then wire the 12 volt power to the converter along with…

view full answer...