What is the Length from the Base of the Flange on Drain Valve # CAM22223 to the Edge of the Thread

Question

Question:

Can you guys tell me how long the whole barbed nipple is on this part?

asked by: Krista

0

Expert Reply:

From the base of the flange on the Camco RV Drain Valve # CAM22223 to the edge of the 3/8" barb thread measures 1-7/8". You can reference the attached photo for a demonstration.

expert reply by: Jon G

0

click to enlarge

Answer 1

When installing the Camco RV Drain Valve w Flange #CAM22223 you would not need to use sealant as long as you use the proper size tubing. Either 1/2 inch or 3/8 inch tubing.

view full answer...

Answer 2

The Camco RV Drain Valve w Flange for 1/2" or 3/8" Diameter Drain Hose - Barb Thread #CAM22223 has a flange measurement is 1 7/8 inch diameter and the measurement of the holes center on center is 1 7/16 inches.

view full answer...

Answer 3

The only difference between the Valterra Universal Barbed Drain Valve #A01-2025VP and the Camco RV Drain Valve - Barbed #CAM22223 is the manufacturer. Apart from that, these are the same drain valves that each have 1/2" and 3/8" diameter…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 11

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 12

To determine which brake assemblies would be needed, you will need to measure your existing brake drums as shown in the provided photo. Since your trailer has a 14,000 lb capacity, you most likely have tandem 7,000 lb axles, which typically use a…

view full answer...